Page 1
TOPRHWS Hardware Manual I Corporation TOPRHWS / TOPRHWS02 Hardware Manual Thank you for purchasing M2I TOPRHWS. Please read this user manual carefully for safe installation, wiring, and operation of this equipment before use. TOPRHWS TOPRHWS02 I Corporation 1 / 19...
3.2 Environment Specifications ............................6 3.3 Structure Specifications ..............................6 Chapter 4 Parts and Detail Specifications ............................6 4.1 TOPRHWS Series ................................6 Chapter 5 Interface with Other Devices............................7 5.1 Serial Communication Specifications ........................7 5.2 Ethernet Communication Specifications ........................ 8 Chapter 6 Block Diagram for Installation ............................
TOPRHWS Hardware Manual Chapter 1 Safety Precautions ■ Before Use For safe operation of the equipment, the user is required to read the contents of this manual thoroughly before use. The safety precautions are for the safe and right use of the product. Therefore, please follow the safety precaution so as to prevent accidents and potential dangers.
Page 4
TOPRHWS Hardware Manual Ambient temperatures lower than 0℃or higher than 50℃and/or on the surface of the control board where a high-pressure device is installed. Where it is continually exposed to an excessive impact or vibration. The space between the rear of the main body and the console box should be at least 100mm for maintenance and ventilation.
TOPRHWS Hardware Manual Chapter 2 Overview 2.1 Product Introduction This product is an industrial equipment required for power supply and communication for TOPRH0700WD FE. Based on RS-232C, RS-422/485, Ethernet, it is aimed primarily to connect, communicate, and control the PLC units through a cable.
TOPRHWS Hardware Manual 번호 Name Description Remarks ① Power Input 24V DC Power Input ② Ext. Function Connector EMG S/W, 3-POS S/W, KEY-Lock, Function1~6 ③ Communication ETHERNET, RS232C/422/485 Cannot be used simultaneously ④ Power S/W TOPRHWS Operating Switch ⑤ TOPRH Connector...
* COM1 and ETHERNET cannot be connected at the same time COM1 or ETHERNET can be selectively used by selecting S/W positioned as seen below. The settings of TOPRH main body and TOPRHWS should be identical. I Corporation 8 / 19...
There are two ways to install the product: one is installing it to a separate panel cut, exposing the front and the other is fixing it to DIN-Rail of the rear. TOPRHWS is connected to TOPRH0700WD FE with predefined 26-fin cable.
TOPRHWS Hardware Manual 6.2 Panel Cut Size for Front Panel Installation Please refer to below drawings for front panel installation. TOPRHWS TOPRHWS02 6.3 Cable Diagram Please check part information of TOPRH0700WD FE connecting cable. 6.3.1 Basic Connector Pin Assignment 6.3.1.1 TOPRH0700WD FE cable connectors (#1)
Page 11
TOPRHWS Hardware Manual PIN NO. SIGNAL. NAME Description Pair Line COMM_0 COM1 or Ethernet SEL #1 PAIR1(+) VCC_IN TOPRH Power IN 24V PAIR3(+) COMM_1 COM1 or Ethernet SEL #2 PAIR1(-) VCC_IN TOPRH Power IN 24V PAIR4(+) COMM_2 COM1 or Ethernet SEL #3...
6.5 Serial and Ethernet Communication Setting Switch 6.5.1 Communication Channel and I/F Setting For SW11 switch, the settings of TOPRH0700WD FE and TOPRHWS should be identical. (1) It can be set for Serial or Ethernet communication. (2) When using serial communication mode, it is possible to use RS-232C/422/485. When Ethernet is selected for communication, COM1 serial communication cannot be used.
Page 14
TOPRHWS Hardware Manual (1) Emergency switch: wiring diagram The emergency switch is a PUSH/PULL switch to stop operation for an emergency. In general, it is wired as follows. Position EMG_A1 EMG_B1 EMG_B2 Not Pressed Open(OFF) Short(ON) Short(ON) Pressed Short(ON) Open(OFF)
Page 15
TOPRHWS Hardware Manual (2) Keylock: wiring diagram For safety, it additionally controls the controllability of the controller. Position Status "A" direction Open(OFF) "B" direction Short(ON) TOPRH KEY LOCK Switch (Sink Type) KEY LOCK KEY LOCK_com PLC DC 제 어 (*It runs with a photocoupler, so it can be controlled only when the main body turns on.) (3) Function key: wiring diagram It additionally controls the controllability of the controller.
Page 16
TOPRHWS Hardware Manual (4) 3-Position switch: wiring diagram For safety, it controls the controllability of the controller. Position 3P_SW_A0 3P_SW_A2 NOT Pressed Open(OFF) Open(OFF) HALF Pressed Short(ON) Short(ON) Fully Pressed Open(OFF) Open(OFF) TOPRH 3-Position Switch (Sink Type) 3P_SW_A1 3P_SW_A1_com PLC DC 제 어 #1...
TOPRHWS Hardware Manual Chapter 7 Installation and Wiring 7.1 Selecting installation Location (1) Where the movement of TOPRH0700WD FE (main body) is secured after it is connected (fixed) to the front panel or DIN-rail of the rear. (2) Where there is no sunlight exposure.
(2) Only an authorized worker by M2I Corporation can check and repair the product in relation to the malfunctions of the product. (3) In case that the problem is not fixed at the site of installation, the equipment can be brought to M2I Corporation for repair.
Copyright: M2I corporation 2022.08 www.m2i.co.kr - When using M2I equipment, read the user manual with care and handle it, paying attention to safety. - Keep the user manual in a safe place so it can be referred to whenever needed.