Summary of Contents for IST MRO001
- Page 1 Instruction Manual Please read and save these instructions. MRO001 Reverse Osmosis System...
- Page 2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modi cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
-
Page 3: Table Of Contents
Contents Installation Instructions Before Installation............................................1 Parts List ................................................2 Product Introduction ............................................2 Installation Sample............................................3 Installation Tips ..............................................3 Installation Steps..............................................4 Step 1: Connect to the Cold Water Supply..................................4 Step 2: Install the Drain Saddle .......................................4 Step 3: Install the RO Faucet ........................................5 Step 4: Connect Tubing..........................................5 Step 5: Start up the system ........................................6 Filter Replacement Schedule........................................6... -
Page 4: Installation Instructions
• Towel • Adjustable wrench, pliers Specifications To achieve optimal performance, it is highly recommended that the system be used only within these operational parameters. Model MRO001 Size (L*W*H) 17.1" *5.5" *14.8" Feed Water Pressure 14.5-87 psi/0.1-0.6 MPa Feed Water Temperature 41-100 °F / 5-38 °C... -
Page 5: Parts List
Parts List MRF2 Preinstalled Part Description Part Description RO ltration unit Pure water tubing（white tubing） Front cover Drain water tubing（red tubing） MCF1 lter RO faucet x1 set MRF2 lter Drain saddle x1 Lock clips x4 Feed water adapter (3/8” and 1/2” x1） Te on tape x1 Inlet water tubing（white tubing）... -
Page 6: Installation Sample
Power indicator The indicator light is always on when the system is powered on. “PURE”water port Connects with polyethylene (PE) tubing “DRAIN”water port Connects with polyethylene (PE) tubing “INLET”water port Connects with polyethylene (PE) tubing Installation Sample Kitchen Faucet RO Faucet Feed Water Adapter Inlet Water Tubing Pure Water Tubing... -
Page 7: Installation Steps
Installation Steps Step 1: Connect to the Cold Water Supply CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water supply to the unit MUST be from the COLD WATER LINE. Using HOT WATER will severely damage your lters. a. -
Page 8: Step 3: Install The Ro Faucet
Step 3: Install the RO Faucet Faucet Spout a. Insert the faucet spout into the faucet body. b. Insert the faucet stem through the hole on the counter top. Faucet Body c. Under the sink, slip on the other parts in the order shown in the Countertop diagram. -
Page 9: Step 5: Start Up The System
Step 5. Start up the system a. Turn on the cold water supply. Check for any leaks in the system. b. Insert the power plug into the socket. NOTE: If the system can’t be powered on after you insert the power plug, check whether there is power owing to the socket under the sink, as this mostly occurs when the power under the sink is powered o . -
Page 10: Filter Replacement Guide
Filter Replacement Guide Turn o faucet and wait for 30 seconds to fully release the pressure on the system. The lter can be replaced without turning o the water source or power supply. a. Twist the lter that needs to be replaced counterclockwise; b. -
Page 11: System Maintenance
System Maintenance If you do not use the machine for a long time (more than 1 week), it is recommended that the faucet be opened to ush for a while before the water is used again. Please replace the lter regularly according to the lter life indicator. NOTE: While testing was performed under standard laboratory conditions, actual performance may vary depend- ing on the source water quality and water usage. -
Page 12: Troubleshooting
Troubleshooting If the System Cannot Be Powered on After You Insert the Power Plug a. Check the ow of electricity to the power outlet under the sink as this problem most often occurs when there is no ow of electricity to the outlet. Also, check to ensure that the system has been plugged correctly into the outlet To test if there is a problem with the system itself, just pick up the system and try another power outlet. -
Page 13: Limited Product Warranty
Booster Pump Starting and Stopping Frequently a. Reminder Buzzer beeps 5 times, and then the lter life indicators on the front panel ash purple. b. There is an internal pressure imbalance: Disconnect the power. Turn o the RO faucet completely, removing any tubing crimps. - Page 14 REVERSE OSMOSIS SYSTEM FOR EASY REORDER FOR EASY REORDER Use the camera app Use the camera app on your smartphone to on your smartphone to scan this QR code. scan this QR code. Use code REORDER for Use code REORDER for 10% off...
- Page 15 主 机 说明 书 此页不印刷 印刷品 技术 要 求 IMPORTANT PRINTING CAUTION 1 . 印 刷 要 求 覆 光 膜 覆 亚膜 U V 油 吸塑油 过油 丝印 2 . 材 质 要 求 封面封底200g铜版纸覆亚膜，内页105g铜版纸 3 . 颜 色 要 求 四色印刷...
Need help?
Do you have a question about the MRO001 and is the answer not in the manual?
Questions and answers