Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MQ Mikasa MT55F
Summary of Contents for MQ Mikasa MT55F
- Page 1 OPERATION MANUAL SERIES MODEL MT55F TAMPING RAMMER (ROBIN EH090D/EH092D GASOLINE ENGINES) Revision #6 (10/01/20) To find the latest revision of this publication or associated parts manual, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
-
Page 2: Proposition 65 Warning
PROPOSITION 65 WARNING PAGE 2 — MT55F RAMMER — OPERATION MANUAL — REV. #6 (10/01/20) -
Page 3: Table Of Contents
TABLE OF CONTENTS MT55F Tamping Rammer Proposition 65 Warning ..........2 Table Of Contents .............3 Safety Information ..........4-7 General Information ..........8 Specifications ............9 Controls and Components ........10 Basic Engine ............11 Operation ............12-15 Maintenance ............16 Troubleshooting Guide ........18-19 NOTICE Specification and part number are subject to change without notice MT55F RAMMER —... -
Page 4: Safety Information
SAFETY INFORMATION Do not operate or service the equipment before reading Potential hazards associated with the operation of this the entire manual. Safety precautions should be followed equipment will be referenced with hazard symbols which at all times when operating this equipment. may appear throughout this manual in conjunction with Failure to read and understand the safety safety messages. - Page 5 SAFETY INFORMATION GENERAL SAFETY ALWAYS know the location of the nearest phone or keep a phone on the job site. Also, know the phone numbers of CAUTION the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency. NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective...
- Page 6 SAFETY INFORMATION ENGINE SAFETY FUEL SAFETY DANGER DANGER The engine fuel exhaust gases contain poisonous carbon DO NOT add fuel to equipment if it is placed inside truck monoxide. This gas is colorless and odorless, and can bed with plastic liner. Possibility exists of explosion or cause death if inhaled.
- Page 7 SAFETY INFORMATION TRANSPORTING SAFETY CAUTION NEVER allow any person or animal to stand underneath the equipment while lifting. NOTICE Before lifting, make sure that the equipment parts (hook and vibration insulator) are not damaged and screws are not loose or missing. Always make sure crane or lifting device has been properly secured to the lifting bail (hook) of the equipment.
-
Page 8: General Information
Construction of Tamping Rammer 1. Use proper lifting techniques to avoid back injury. This The Mikasa MT55F is equipped with an air cooled, two cycle handle is for manual lifting only. gasoline engine. Transmission of the power takes place by increasing the engine speed to engage the centrifugal clutch. -
Page 9: Specifications
SPECIFICATIONS c i f i t a s s s s s l l a . n i l l a . n i o r t ) t h . t f ) n i b / . t u l c i t f i r t y t i... -
Page 10: Controls And Components
COMPONENTS Figure 1. MT55F Rammer Figure 1 shows the location of the controls and components 8. Fuel Tank/Cap – Remove this cap to add unleaded gaso- for the MT55F Tamping Rammer. The functions of each control line to the fuel tank. Make sure cap is tightened securely. DO is described below: NOT over fill. -
Page 11: Basic Engine
BASIC ENGINE Figure 2. Engine Controls and Components INITIAL SERVICING The engine (Figure 2) must be checked for proper lubrication and Recoil Starter (pull rope) – Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and filled with fuel prior to operation. -
Page 12: Operation
OPERATION Fuel This section is intended to assist the operator with the initial start-up of the MT55F Tamping Rammer. It extremely important 1. Fill the fuel tank (Figure 4) with unleaded gasoline. DO NOT that this section be read carefully before attempting to operate overfill, wipe up spilled fuel immediately. - Page 13 OPERATION Initial Start-up When starting the MT55F Tamping Rammer perform the following: Open the fuel shut- off valve by moving the fuel cock lever to the open position (Figure 7). Figure 6. Engine Oil Dipstick (Oil Level) r o t l i o i h ( s a l...
- Page 14 OPERATION Figure 9. Throttle Lever (Idle) Figure 11. Recoil Starter 4. In cold weather, start the unit with choke lever "Fully Closed"(Figure 10). In warm weather or when the engine is warm, the unit can be started with choke halfway or com- 6.
- Page 15 OPERATION 2. After the engine cools , turn the engine start/stop switch to the CAUTION - Throttle Lever “OFF” position (Figure 14). Make sure that the throttle lever is moved to the FULL OPEN position. Operating the rammer at less than full speeds can result in damage to the clutch springs or foot 2.
-
Page 16: Maintenance
MAINTENANCE Maintenance Perform the scheduled maintenance procedures as indicated: PAPER ELEMENT DAILY GRAY OUTER ■ Thoroughly remove dirt and oil from the engine and control FOAM ELEMENT area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the spring box and bellows for oil leaks. - Page 17 NOTES MT55F RAMMER — OPERATION MANUAL — REV. #6 (10/01/20) — PAGE 17...
-
Page 18: Troubleshooting Guide
TROUBLESHOOTING c i f t l u t r a i t i n i r b i t i n i s o o i t i c a l o i t i l i a l i w . - Page 19 TROUBLESHOOTING ENGINE ENGINE ENGINE ENGINE ENGINE i t n i t a f s i e r r v e l . r e i r p v i t o i t o i t u l f l f l r r e i t a n i l...
- Page 20 © COPYRIGHT 2020, MULTIQUIP INC. Multiquip Inc , the MQ logo and the Mikasa logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.
Need help?
Do you have a question about the Mikasa MT55F and is the answer not in the manual?
Questions and answers