Summary of Contents for BakerStone Original Series
Page 1
Original Series Outdoor Multi-function Cooking Center Product Guide Model # BSO4501-EBK-OOO-000 Important, Retain for Future Reference: Read Carefully WARNING: This product guide contains important information necessary for the proper assembly and safe use of the appliance. Read and follow all warnings and instructions before assembling and using the appliance.
Page 2
WARNINGS Failure to follow these instructions could result in fire or explosion which could cause property damage, personal injury or death. The installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1, or the Propane Storage and Handling Code,CSA B149.2, or the Standard for Recreational Vehicles, ANSI A119.2/NFPA 1192, and CSA Z240 RV Series, Recreational Vehicle Code, as applicable.
Page 3
Do not use any cleaning agents or other liquids to clean the stones. Do not place gasoline, alcohol, wood products, charcoal or any other combustible material (unless BakerStone approved) in the baking chamber. Remove any appliance cover and place at least 10 feet (3 Meters) from appliance before use.
Table of Contents Page What’s in the package Assembly of the Grill Assembly of the Pizza Oven Box LP Gas Cylinder Requirements LP Gas Cylinder Placement LP Gas Cylinder Connection LP Gas Leak Test Pre-Use Safety Checks Lighting Instructions How to Use The Pizza Oven Box Routine Care &...
What’s in the package Before assembly, ensure that all parts below are included. Please note part numbers are not listed in numerical order. For a complete parts diagram and part list for customer service needs such as replacement parts please go to page 28. Firebox Assembly 50 - Griddle 53 - Griddle Cover Assembly...
Page 7
36 - Rear Beam 30 - Firebox Support 11 - Drip Tray 28 - Gas Cylinder (x2) Support Hook (x2) 35 - Table 10 - Folding Table 24 - Right Door Support Right (x2) (x2) 6 - Control Knob 33 - Drip Tray 37 - Grill 39 - Griddle (x6)
Assembly of the Grill STEP 1. Attach the CASTERS (23) to the RIGHT SIDE FRAME (26). STEP 2. Attach the WHEEL (19), WHEEL AXLE (18) to the LEFT SIDE FRAME (16) using NUTS (GG). Next place the CAPS (20) onto the wheels. STEP 3.
Page 9
STEP 5. Attach the CABINET FRONT PANEL (32) to the BASE PANEL (22) and SIDE FRAME (26) using SCREWS (DD). STEP 6. Attach the CABINET MIDDLE PANEL (27) to the BASE PANEL (22) and CABINET FRONT PANEL (32) using SCREWS (DD).
Page 10
STEP . STEP . STEP 10. Attach the FRONT BRACE (12) to the SIDE FRAMES (16 and 26), FRONT CABINET PANEL (32) and CABINET MIDDLE PANEL (27) using fasteners (AA) and (DD) as shown.
Page 11
STEP 11. Attach the REAR BEAM (36) using SCREWS (DD). STEP 12. Attach the FIREBOX SUPPORTS (30) using SCREWS (DD) to the SIDE FRAMES (16 and 26). STEP 13. Attached the DRIP TRAY SUPPORTS (11) using SCREWS (AA).
Page 12
STEP 14. and place onto the assembled cart. STEP 15. Attach the FIREBOX ASSEMBLY using 4 SCREWS (DD) on each side. STEP 16. Secure the HOSE CLIP (41.3) using SCREW ( WARNING: FAILURE TO ATTACH PROPERLY MAY RESULT IN A 41.3 BURNT OR MELTED HOSE, WHICH MAY RESULT IN FIRE AND/ OR INJURY.
Page 13
STEP 17. Attached the GAS CYLINDER HOOK (28). STEP 18. Attach the TABLE SUPPORT LEFT (34) and RIGHT ). NOTE: (35) to each side of the grill using SCREWS ( Ensure e facing upwards when STEP 19. Hang the FOLDING TABLES (10) onto the TABLE SUPPORTS.
Page 14
STEP 20. Attach MATCH LIGHT CHAIN (57) to RIGHT DOOR (24) using SCREW (JJ). STEP 21. Attached the LEFT DOOR (25) and RIGHT DOOR(24) by aligning the bottom hinge into the hole in the BASE (22) and then pressing down on the top hinge while aligning it with the hole in the FRONT BRACE (12).
Page 15
STEP 24. Insert the GRIDDLE GREASE CUP (39) into the front side of the grill assembly. STEP 25. Loosen the pre-assembled SCREWS from the HANDLE (53.2) and then attach the HANDLE (53.2) to the GRIDDLE COVER (53.1) using the SCREWS. 53.2 Place the GRIDDLE COVER (53) on top of the firebox when the GRIDDLE (50) or PIZZA OVEN BOX (54) is not in use.
Assembly of the Pizza Oven Box STEP 1 - Place the STONE CRADLES (54.6) into the HOUSNIG (54.5), and fasten with 8 SCREWS (KK) and 8 FLAT WASH- ERS (LL). 54.5 54.6 STEP 2 - Insert the TOP STONE (54.2) into the housing, resting on the stone cradles.
Page 17
STEP 5 - Insert the BASE STONE (54.8) into the notches of the 2 side stones. 54.8 STEP 6 - Fasten the BACK PANEL (54.1) housing with 4 SCREWS (KK) and 4 FLAT WASHERS (LL). 54.1 54.9 STEP 7 - Locate the VENT CATCH (54.9) and place into the vent of the oven and resting on the base stone.
LP Gas Cylinder (tank) Requirements The appliance is only to be fueled by an LP (liquid propane) gas cylinder measuring 12” (30.5cm) diameter and 18” (45.7cm) high with a 20lb. (9.1kg) capacity. The gas cylinder (tank) must incorperate a Type 1 cylinder valve and an over filling protection device (OPD). The LP gas cylinder must be constructed and marked in accordance with the Specifications for LP gas Cylinders of the U.S.
LP Gas Cylinder Placement Place the LP Gas Cylinder into the Base and secure with the rim of the LP Gas Cylinder. WARNING: The pressure regulator and hose assembly supplied with the appliance must be used. Replacement pressure regulators and hose assemblies shall be those specified by the appliance manufacturer.
LP gas cylinder connection: Step 1. Ensure the LP cylinder used conforms to the requirements listed on the previous page. Also inspect the LP gas cylinder valve rubber seal for deterioration such as cracks, deformation or tears. Step 2. Inspect the LP gas cylinder valve to ensure the threads match that of the included hose and regulator.
LP Gas Leak Test is reconnected or changed the LP gas Leak Test must be performed. Do not use an open flame to check for leaks. Do not smoke or be in the presence of any ignition sources while performing a leak test. Perform leak test outdoors in a well ventilated area.
LIGHTING INSTRUCTIONS before lighting. For the grill, open lid during lighting. STEP 1 STEP 2 STEP 3 Push and turn one of the burners to (HIGH) [see Figure - 4] while pressing and holding the (IGNITION) button [See Figure - 5]. Figure - 4 STEP 4 Once burner lights release the (IGNITION) button.
Page 23
For best results, we recommended seasoning the griddle before cooking on griddle top. Make sure griddle top is wiped clean of debris. (Please reference the Cleaning Your Griddle section Ignite griddle by following lighting instruction Turn all knobs to set burners to high.
NEVER cover slots, holes, or passages in the oven bottom or cover Doing so blocks air flow through the oven and may cause carbon monoxide poisoning. WARNING Aluminum foil linings may trap heat causing a fire hazard. How to use the Pizza Oven Box WARNING: Please completely read all safety precautions at the beginning of and throughout this...
Page 25
STEP 6 Using the pizza peel, launch your pizza into the appliance [see Figure - 10]. NOTE: This can be accomplished by placing the pizza peel just over half-way into the appliance, and using a quick of the appliance. See www.bakerstonebox.com website for a video demostration.
STEP 10 When finished baking, turn the burners on the [see Figure - 13] and allow the appliance to cool for a period of at least ninety (90) minutes. NOTE: If cleaning is required, leave the burners on and continue to heat the oven for 15 minutes prior cool for a period of at least ninety (90) minutes [See Care and Cleaning instructions].
Page 27
CLEANING YOUR GRIDDLE FIRST TIME CLEANING GRIDDLE COOKING SURFACE: WARNING Our Griddles are pre-treated with cooking oil to prevent rust and damage during shipping. For first time use, wash griddle with hot soapy water. THIS IS THE ONLY TIME YOU SHOULD USE SOAP ON THE GRIDDLE COOKING SURFACE.
Periodic Care & Cleaning of burner system This appliance will periodically require more detailed cleaning check and clean burner/venturi tubes for insects and insect nests. WARNING: A clogged tube can lead to a fire beneath the appliance. Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
STEP 6 any debris or dirt. Inspect the burners for any cracks or holes that appear out of place. If cracks or holes are present replace the Burner. STEP 7 wire or small bottle brush into the inlet portion of the Burner. Compressed air may also be used to clean the burners by blowing air into the inlet portion of the burner and the air will flow out of the venturi holes.
Customer Service Parts Identifier Please use the below diagram and legend on the following pages to identify replacement parts when contacting our customer service team.
Page 31
PART# DESCRIPTION PART# DESCRIPTION Lid Assembly (includes BG3024B-CSB-01 BG3024B-CSB-36 Rear Beam 1.1-1.6) BG3024B-CSB-1.1 Lid Axis BG3024B-CSB-37 Grease Cup BG3024B-CSB-1.2 Lid Panel BG3024B-CSB-38 Electronic Ignitor BG3024B-CSB-1.3 Spacer BG3024B-CSB-39 Grease Cup _Griddle Heat Shield_Secondary BG3024B-CSB-1.4 Temperature Gauge BG3024B-CSB-40 Firebox Gas Valve & Regulator BG3024B-CSB-1.5 Lid Handle Shield BG3024B-CSB-41...
BakerStone. NOTE: Slight chips or scratches in the stones are not considered damages and do Claims for defects or missing items must be accompanied by the original or an acceptable copy of the sales receipt and photographs must be taken to support any and all claims submitted.
Page 33
Disclaimer Use of this appliance is at the discretion of the user. BakerStone is not responsible for personal injury or property damage resulting from the misuse of this appliance. FAILURE TO NOT FOLLOW THE PRECAUTIONS AND INSTRUCTIONS IN THE PRODUCT GUIDE MAY RESULT IN THE VOIDING OF THE WARRANTY OF THIS APPLIANCE.
Frequently Asked Questions Why is my Pizza Oven Box not lighting? - LP Gas Cylinder out of fuel. - Excess flow limiting device may have been activated. To deactivate: 1. Turn all burners to the OFF position. 2. Close LP Gas Cylinder valve and disconnect regulator. 3.
Need help?
Do you have a question about the Original Series and is the answer not in the manual?
Questions and answers