Summary of Contents for SKF LINCOLN 84827 Series
- Page 1 User and maintenance instructions Pump hoist Model 84827*, 400 lb. drum sized, air operated, manually controlled Date of issue July 2022 Form number 403849 Version * Indicates change.
-
Page 2: Table Of Contents
Contents Declaration of Incorporation* ..U.K. Declaration of Incorporation* . . . Signal words for safety ... . . Safety ......Specifications . -
Page 3: Declaration Of Incorporation
5148 N. Hanley Road St. Louis, MO 63134 U.S.A. TEL: +1 (314) 679-4200 FAX: +1 (314) 679-4367 Authorized to compile the technical file: SKF Lubrication Systems Germany GmbH Heinrich-Hertz-Straße 2-8 69190 Walldorf, Germany TEL: +49 (0) 6227-330 EMAIL: robert.collins@skf.com WEBSITE: www.skf.com... -
Page 4: U.k. Declaration Of Incorporation
Lincoln Industrial Corporation 5148 N. Hanley Road St. Louis, MO 63134 U.S.A. TEL: +1 (314) 679-4200 FAX: +1 (314) 679-4367 Authorized to compile the technical file: SKF (U.K.) Limited 2 Canada Close Banbury, Oxfordshire, OX16 2RT, GBR EMAIL: robert.collins@skf.com WEBSITE: www.skf.com This U.K. -
Page 5: Signal Words For Safety
Safety Explanation of signal NOTE* Do not operate equipment without words for safety wearing personal protective gear. Read and carefully observe these installation Wear eye protection. Protective instructions before installing/operating/ equipment such as dust mask, non-skid troubleshooting the assembly. The assembly safety shoes, hard hat, or hearing NOTE must be installed, maintained and repaired... -
Page 6: Specifications
Installation Specifications Height of unit in lowered position 73 in (1 854 mm) in (2 807 mm) Height of unit in raised position Base casting can be used as a tem plate to Hoist capacity 400 lbs. (181 kg) mark location of anchor bolts. Operating air pressure 40 psi (2,8 bar) minimum, 200 psi (13,7 bar) maximum. -
Page 7: Kit 2719
Fig. 2 Kit 2719* For use with PileDriver pumps (refer to application chart) Item Description Pump mounting bracket (refer to chart) Quarter turn valves Air inlet plug Coupling socket Air supply line Base casting Follower * Indicates change. Fig. 3 Mounting template 16 / in (425 mm) -
Page 8: Install Follower To Pump Tube
Install follower to Prime pump 4 Shut off valve to lop hoist. 5 Disconnect air coupler to hold hoist in pump tube raised position. 1 Open bleeder plug in pump outlet. 2 Operate pump until material flows from plug opening. To lower pump and follower 3 Shut off pump. -
Page 9: Service Parts
Service parts Item Description Part no. Qty. Item Description Part no. Qty. Screw 50038 Set screw 50524 Air hose 237172 Nipple 10130 Restrictor 13345 Line check 83995 Tube 271467 Adapter 16362 Packing 34327 Washer, packing 48039 Tube cap 40446 51014 Tube connector 243699 Wiper ring... -
Page 10: Kits 1716 And 2716
Fig. IPB 1 Kits 1716 and 2716* Before operation, install 243599 fitting into top of pump hoist. Insert 271467 tubing into fitting. Air motor Mounting bracket Note: Kit 1716 consists of 49, 8 and mounting bracket 84391. Kit 2716 consists of 49, 8 and support bracket 84785. Kit 2719 consists of 50, 8 and support bracket 84785.* Indicates change. -
Page 11: Kit 2719
Fig. IPB 2 Kit 2719* A−A B−B C−C Before operation, install 243599 fitting into top of pump hoist. Insert 271467 tubing into fitting. Air motor Mounting bracket Note: Refer to service manual - 412843 for low level air cutoff kits. Indicates change. -
Page 12: Warranty
® SKF and Lincoln are registered trademarks of the SKF Group. © SKF Group 2022 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.
Need help?
Do you have a question about the LINCOLN 84827 Series and is the answer not in the manual?
Questions and answers