Advertisement
LoRa Mipot USB-DONGLE USER'S MANUAL
Code: 32001388
INTRODUCTION:
This USB-Dongle has been developed to test the functionality and radio parameters of the
transceiver 32001345.
The unit interfaces with the PC via USB port and can be configured using a GUI.
The USB-Dongle comes in two different hardware
on the printed circuit board and the second with the SMA connector.
1. ABSOLUTE MAXIMUM RATINGS
Power supply
RF input (SMA connector)
Storage temperature
Operating temperature
2. ELECTRICAL CHARACTERISTICS
Parameter
External supply voltage on USB
RF Output Power
Please refer to 32001345 LoRa module datasheet for more information about commands,
radio parameters and electrical characteristics.
Mipot S.p.A. reserve the right to modify the specifications without notice
designs.
The first with
+ 5.25 V
+10 dBm
-10 ÷ +55° C
-10 ÷ +55° C
Min.
Typ.
4
5
0
-
Page 1 of 10
LoRa Mipot
868 MHz
antenna integrated
Max.
Unit
5.25
Volt
14
dBm
Cormòns, April,10, 2019
Rev. 1.0
Notes
Advertisement
Table of Contents
Summary of Contents for MIPOT 32001388
- Page 1 5.25 Volt RF Output Power Please refer to 32001345 LoRa module datasheet for more information about commands, radio parameters and electrical characteristics. Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 1 of 10...
- Page 2 ➢ Choose SiLabs-CDCInstaller_x86 if your operating system is 32 bit. ➢ Click on NEXT. ➢ Check the box “I accept the agreement” the click on NEXT. Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 2 of 10...
- Page 3 ➢ To get an help description, click on the question mark icon near the desidered field. 6. GRAPHIC USER INTERFACE – MAIN FUNCTIONS Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 3 of 10...
- Page 4 [AA] protocol header [33] command id [02] command lenght [00] EEPROM start address [08] number of bytes to be read [18] checksum Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 4 of 10...
-
Page 5: Pairing Procedure
➢ Set Power (dBm) to 14dBm in “Radio Config” page. ➢ Now the END-NODE is ready to be paired to the MASTER (see section below). 9. PAIRING PROCEDURE Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 5 of 10... - Page 6 If the END-NODE device is correctly paired, the serial number of the master’s module displayed in the MST(HEX) indicator Box (END-NODE GUI). Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 6 of 10...
- Page 7 If the number of received message is less than <Msg Th> the result of the test is negative. TEST PASS = TEST FAIL Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 7 of 10...
-
Page 8: Message Transmission
➢ Send the confirmed or unconfirmed message by pushing selected buttons in the END-NODE table. Message will be displayed in the master tab. Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 8 of 10... -
Page 9: Mechanical Dimensions
All mechanical dimensions are expressed in [mm]. Please refer to 32001345 LoRa module datasheet for more informations about commands, radio parameters and electrical characteristics. 13. REVISION HISTORY Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 9 of 10... - Page 10 Rev. 1.0 10 APRIL 2019 Rev.1.0 Cormòns, April,10, 2019 Mipot S.p.A. reserve the right to modify the specifications without notice Page 10 of 10...
Need help?
Do you have a question about the 32001388 and is the answer not in the manual?
Questions and answers