Related Manuals for IBT IB700
Summary of Contents for IBT IB700
- Page 1 I B 7 0 0 Full-Size Socket 370 CPU Card With Optional VGA/LAN/SCSI U S E R ’S M A N U A L Version 1.0B...
- Page 2 Intel and Celeron are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation. All other product names or trademarks are properties of their respective owners. IB700 User’ s Manual...
-
Page 3: Table Of Contents
Product Description ............1 Checklist ................2 Specifications ..............3 Board Dimensions............4 Installations..............5 Installing the CPU............6 MicroPCI Daughter Card Installation .......6 Installing the Memory (DIMM)........7 Setting the Jumpers............8 Connectors on IB700 ............ 14 Watchdog Timer Configuration ........28 IB700 User’ s Manual... - Page 4 This page was intentionally left blank. IB700 User’ s Manual...
-
Page 5: Introduction
MTBF, lower power consumption, cost effective for small capacity and small form factor. The IB700 CPU card is designed with all components placed on a single side, thus, offering stable performance in a harsh industrial environment. -
Page 6: Checklist
INTRODUCTION Checklist Your IB700 package should include the items listed below. • The IB700 Industrial CPU Card • This User’s Manual • 1 IDE Ribbon Cable • 1 Floppy Ribbon Connector • 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a Mounting Bracket •... -
Page 7: Specifications
Support M-Systems 2MB~144MB DiskOnChip flash disk SSD Interface Watchdog timer, ISA high drive, PICMG compliance Other Features Full Size Form Factor 338mm x 122mm (13.3” x 4.8”) Dimensions +5V : 12A (max) Power +/-12V : 200mA (max) Requirements IB700 User’ s Manual... -
Page 8: Board Dimensions
INTRODUCTION Board Dimensions IB700 User’ s Manual... -
Page 9: Installations
INSTALLATIONS Installations This section provides information on how to use the jumpers and connectors on the IB700 in order to set up a workable system. The topics covered are: Installing the CPU............6 MicroPCI Daughter Card Installation .......6 Installing the Memory (DIMM)........7 Setting the Jumpers............8... -
Page 10: Installing The Cpu
INSTALLATIONS Installing the CPU The IB700 CPU card supports a Socket 370 processor socket for Intel Celeron/Coppermine processors. The Socket 370 processor socket comes with a lever to secure the processor. Raise this lever to about a 90° angle to allow the insertion of the processor. -
Page 11: Installing The Memory (Dimm)
INSTALLATIONS Installing the Memory (DIMM) The IB700 CPU Card supports three 168-pin DIMM socket for a maximum total memory of 768MB in SDRAM type. The memory module capacities supported are 32MB, 64MB, 128MB and 256MB. Installing and Removing DIMMs To install the DIMM, locate the memory slot on the CPU card and perform the following steps: 1. -
Page 12: Setting The Jumpers
INSTALLATIONS Setting the Jumpers Jumpers are used on IB700 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on IB700 and their respective functions. -
Page 13: Jumper Locations On Ib700
INSTALLATIONS Jumper Locations on IB700 JP10, JP11, JP12: RS232/422/485 (COM2) Selection JP9: External Battery Connector JP8: Clear CMOS Content JP5: Watchdog Selection JP6: DiskOnChip Address Select DSW1 (3): CPU Bus Speed Selector DSW1 (5-8): CPU Frequency Selector IB700 User’ s Manual... -
Page 14: Dsw1 (3): Cpu Bus Speed Selector
7.5X 500MHz 750MHz xx xx xx xx on off off off 533MHz 800MHz xx xx xx xx off on on off *IB700 BIOS can detect 850MHz CPU and no switch setting is required. IB700 User’ s Manual... -
Page 15: Jp3: Onboard Lan Enable/Disable (Ibd99)
JP4: Onboard C&T VGA Enable/Disable (IBD99) Setting VGA Function Pin 1-2 Enabled Short/Closed Pin 2-3 Disabled Short/Closed JP5: Watchdog Selection Setting Function Pin 1-2 Reset Short/Closed Pin 2-3 Short/Closed JP6: DiskOnChip Address Select Address D0000-D7FFF D8000-DFFFF (default) IB700 User’ s Manual... -
Page 16: Jp8: Clear Cmos Content
COM2 RS-232 RS-422 RS-485 Function JP10: JP10: JP10: Jumper Setting JP11: JP11: JP11: (pin closed) 3-5 & 4-6 1-3 & 2-4 1-3 & 2-4 JP12: JP12: JP12: 3-5 & 4-6 1-3 & 2-4 1-3 & 2-4 IB700 User’ s Manual... -
Page 17: Jp2: Lcd Power Setting (Ibd99/69)
INSTALLATIONS JP2: LCD Power Setting (IBD99/69) The IBD99/69 C&T 69000 VGA MicroPCI daughter card supports 5V and 3.3V power. Use JP2 to select the power setting. 3.3V Setting 5V Setting IB700 User’ s Manual... -
Page 18: Connectors On Ib700
INSTALLATIONS Connectors on IB700 The connectors on IB700 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on IB700 and their respective functions. Connector Locations on IB700..............15 J1: System Function Connector............16... -
Page 19: Connector Locations On Ib700
INSTALLATIONS Connector Locations on IB700 J19: RJ45 Connector J18: VGA CRT Connector J16: PS/2 Mouse Connector J17: PS/2 Mouse External Connector J15: PS/2 Keyboard Connector J14: COM2 Serial Port Connector J13: COM1 Serial Port Connector J12: Parallel Port Connector J11: P8 AT Power Connector... -
Page 20: J1: System Function Connector
Power LED and Keylock: Pins 11 - 15 The power LED indicates the status of the main power switch. The keylock switch, when closed, will disable the keyboard function. Pin # Signal Name Power LED No connect Ground Keylock Ground IB700 User’ s Manual... - Page 21 Reset Switch: Pins 9 and 19 The reset switch allows the user to reset the system without turning the main power switch off and then on again. Orientation is not required when making a connection to this header. IB700 User’ s Manual...
-
Page 22: J2: External Keyboard Connector
Signal Name Keyboard clock Keyboard data J3: CPU Fan Power Connector J3 is a 3-pin header for the CPU fan. The fan must be a 12V fan. Pin # Signal Name Rotation +12V 1 2 3 Ground IB700 User’ s Manual... -
Page 23: J4, J5: Eide Connectors
Host data 15 Ground DRQ1 Ground Host IOW Ground Host IOR Ground IOCHRDY Host ALE DACK1 Ground IRQ15 No connect Address 1 No connect Address 0 Address 2 Chip select 0 Chip select 1 Activity Ground IB700 User’ s Manual... -
Page 24: Jp4: Irda Connector
1 2 3 Wake on LAN J8: System Fan Power Connector J8 is a 3-pin header for the system fan. The fan must be a 12V fan. Pin # Signal Name Rotation +12V 1 2 3 Ground IB700 User’ s Manual... -
Page 25: J9: Floppy Drive Connector
Write gate Ground Track 00 Ground Write protect Ground Read data Ground Side 1 select Ground Diskette change J10: External ATX Power Connector Pin # Signal Name 5VSB (Standby +5V) 1 2 3 PS-ON (soft on/of) Ground IB700 User’ s Manual... -
Page 26: J11: P8 At Power Connector
PD2, parallel data 2 Select PD3, parallel data 3 Ground PD4, parallel data 4 Ground PD5, parallel data 5 Ground PD6, parallel data 6 Ground PD7, parallel data 7 Ground ACK, acknowledge Ground Busy Ground Paper empty Ground Select IB700 User’ s Manual... -
Page 27: J13, J14: Com1, Com2 Serial Port
INSTALLATIONS J13, J14: COM1, COM2 Serial Port J13 and J14, both 10-pin headers, are the onboard serial port connectors of the IB700. The following table shows the pin assignments of these connectors. Pin # Signal Name fixed as RS-232 RS-422... -
Page 28: J17: Ps/2 Mouse External Connector
The figure below shows the pin out assignments of this connector and its corresponding input jack. TD+(pin#1) Link LED TD-(pin#2) RD+(pin#3) RD-(pin#6) Active LED J20, J21: MicroPCI Connectors J20 and J21 are MicroPCI connectors supporting MicroPCI daughter cards with VGA, Ethernet or SCSI function. IB700 User’ s Manual... -
Page 29: J1: Lcd Panel Connector (Ibd69)
The IBD69 C&T 69000 VGA MicroPCI daughter card supports LCD panels. Use J1 to connect the system to an LCD panel. Signal Name Pin # Pin # Signal Name 5V or 3.3V 5V or 3.3V SHFCLK ENABKL FPVDD FLM(V SYNC) FPVEE LP(H SYNC) +12V +12V IB700 User’ s Manual... -
Page 30: Flat Panel Display Interface Pin Descriptions
WakeOnLAN connector. The following table shows the pin out assignments of this connector. WakeOnLAN will function properly only with an ATX power supply with 5VSB that has 800mA. Pin # Signal Name +5VSB Ground 1 2 3 Wake on LAN IB700 User’ s Manual... -
Page 31: J1: Ultra2 Scsi Connector (Ibd60)
GROUND LVTRMPWR LVTRMPWR LVTRMPWR LVTRMPWR N.C. GROUND GROUND LVATNP LVATNM GROUND GROUND LVBSYP LVBSYM LVACKP LVACKM LVRSTP LVRSTM LVMSGP LVMSGM LVSELP LVSELM LVCDP LVCDM LVREQP LVREQM LVIOP LVIOM LVDP8 LVDM8 LVDP9 LVDM9 LVDP10 LVDM10 LVDP11 LVDM11 IB700 User’ s Manual... -
Page 32: Watchdog Timer Configuration
The following describes how the timer should be programmed. Enabling Watchdog: AX, 000FH (Choose the values from 0) DX, 0443H DX, AX Disabling Watchdog AX, 00FH (Any value is fine.) DX, 0441H DX, AX WATCHDOG TIMER CONTROL TABLE Level Value Time/sec Level Value Time/sec IB700 User’ s Manual... - Page 33 APPENDIX IB700 User’ s Manual...
Need help?
Do you have a question about the IB700 and is the answer not in the manual?
Questions and answers