BlackVue Power Magic EZ - Super Easy Power Link For Parking Mode Manual

Settings

Parking Mode

Parking Mode Switch ON
Parking mode enabled
When the ignition is off: The Power Magic EZ powers your dashcam in parking mode.

Driving mode enabled
When the ignition is on: The Power Magic EZ powers your dashcam in driving mode.

Parking Mode Switch OFF
Parking mode disabled
When the ignition is off: The Power Magic EZ blocks power from your dashcam.

Driving mode enabled
When the ignition is on: The Power Magic EZ powers your dashcam in driving mode.

Timer Settings

Cut-off Voltage Settings

Installation

1. Locate the OBD-II port and plug in the Power Magic EZ
   The OBD-II port is normally located just below the driver-side interior fuse panel (location may depend on your vehicle).
   
2. Plug the Power Magic EZ's power cable to the dashcam's DC-in port
   Neatly run the Power Magic EZ's power cable to the dashcam's position and plug it into the dashcam.
   

Plug the Power Magic EZ into your OBD-II Port and you are ready to use your dashcam when the engine is off. A low voltage power cut-off function and a parking mode timer protect your car battery from discharge.

Using the Parking Mode Switch you can easily enable/disable parking mode, without affecting drive recording auto-start at ignition.

Specifications

Rated output voltage: 12-24 V DC

Power cut-off timer setting: 6 hoursinfinity

Output current/Quiescent current: Rated: 1A(Maximum: 3A)/ Below 300µA

Power cut-off voltage (based on the input voltage): 12V, 12.5V(±0.1V)/22.8V,23.2V(±0.1V)

DC connector type: DC 12 V-24 V

(DC Plug: (Ø3.5 x Ø1.35))

Country of origin: Republic of Korea

Warranty: 1 year manufacturer's warranty

Notice

This company will not be liable for any damage arising from not following this instruction manual.

In some regions the use of the OBD-II port to power accessories may be penalized during a vehicle inspection. It is recommended that the Power Magic EZ be removed from the ODB-II port before a vehicle inspection is carried out.

Settings

Before adjusting the cut-off voltage and timer switches, ensure you turn the Parking Mode Switch OFF and unplug the Power Magic EZ.

Parking Mode Switch
The Parking Mode Switch lets you easily enable/disable parking mode without affecting drive recording. Regardless of whether the switch is ON or OFF, the Power Magic EZ detects when your start your engine and automatically powers your dashcam while driving.

Power Cut-Off Settings
The Power Magic EZ will power your dashcam in parking mode until either your car battery voltage drops to the configured value or the configured timer elapses (whichever occurs first).

Installation Guide

*Only compatible with vehicles which use the CAN bus protocol.

*Make sure the engine is off and accessory power is off before proceeding.

*This product may not be compatible with your dashcam's power connector.

Please check your dashcam's DC power connector size and type before using.

1. Locate the OBD-II port and plug in the Power Magic EZ
   The OBD-II port is normally located just below the driver-side interior fuse panel (location may depend on your vehicle – please refer to your owner's manual).
   After plugging in the Power Magic EZ, push in the white locking tab to secure it in place.
   ※If the position of the Power Magic EZ prevents you from closing the fuse panel cover, disconnect the Power Magic EZ then remove the OBD-II port from it's mounting hole by reaching behind it and squeezing both sides while pushing the port in. You should then be able to plug in the Power Magic EZ and close the fuse panel cover.
2. Plug the Power Magic EZ's power cable to the dashcam's DC-in port Neatly run the Power Magic EZ's power cable to the dashcam's position and plug it into the dashcam.

LED Status Indicator

Driving Mode: LED is green when starting the car and whilst driving

Parking Mode: LED blinks green during parking mode

Cut-Off Mode: LED blinks red for 1 minute after cutting off power in accordance with the Timer or Voltage Cut-Off settings (after 1 minute the LED turns off)

※Depending on your vehicle model, there may be a slight delay when switching between modes.

FCC Compliance Information

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Finally, any changes or modifications to the equipment by the use not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC ID: YCK-PMEZ

FCC ID: YCK-PMEZ

Manufacturer
Pittasoft Co., Ltd. / South Korea

Address
7F, BYC HIGHCITY Building A 131, Gasan Digital 1-ro, Geumcheon-gu, Seoul, Republic of Korea, 08506

Customer Support
cs@pittasoft.com

facebook.com/BlackVueOfficial

www.blackvue.com

Made in Korea