DELTA DORE Easy Bulb E27CW, E14CW, GU10CW - Smart LED Lamp Manual

Technical specifications

Electrical specifications

• Rated volatage: 220 V - 240 V
• Network frequency: 50 Hz - 60 Hz
• Stand-by consumption: < 0.5 W
• Power consumption acccording to version*:
  Easy Bulb E27CW = 8.5 W
  Easy Bulb E14CW = 4.8 W
  Easy Bulb GU10CW = 4.8 W
• Room temperature allowed: -20°C to + 40°C
• Connectivity: Zigbee 3.0
• Transmission frequency:
  2400-2483,5MHz
• Maximum wireless power 10 mW- Wireless range: up to 30 m depending on building materials.

Lighting specifications

• Luminous flux depending on version*:
  Easy Bulb E27CW = 806 lm
  Easy Bulb E14CW = 470 lm
  Easy Bulb GU10CW = 350 lm
• Colour temperature: 1800 - 6500 K

Google Play is a registered trademark of Google LLC. App Store is a service mark of Apple Inc.

Use voice control or a smartphone to control lighting remotely.

• Stop/Start
• Change colour to create the desired lighting atmosphere
• Adjust white light temperature settings
• Dimmable lighting to adjust the light intensity
• Programming
• Planned scenarios

Installation

This product should only be installed indoors.

1. Turn off the light you want to put the smart bulb in then unscrew the old bulb.
   
2. Screw in the smart lamp.
   
3. Turn on the lamp, after a short colour cycle, the light will flash then give off a white light.
   

The lamp is waiting to pair.

Pairing with the Tydom app

Download the Tydom app.

Depending on your device: Go to Google Play or the App Store and search for and download the free "Tydom" app.

Make sure that your smartphone/tablet is connected to the local network. Launch the Tydom app.

Go to the "Settings" page of your installation, select "Add a device" >Lighting> Smart lamp, then follow the instructions.

Leave the switch on to control the bulb remotely via the Tydom app.

Reset

• Turn on the light using the switch.
• Turn the light on and off 6 times in succession.
• Leave the light on.
  After a short colour cycle, the light will flash then give off a white light.

The lamp is waiting to pair.

Risk of fire / burns and/or explosion.

• Do not attempt to repair the unit yourself; an after-sales service is available.
• Never use defective or damaged LED lamps.
• Do not allow the LED lamps to come intocontact with water or other fluids.
• The LED lamps must not be dimmed with conventional dimmers.

UK Statutory Instruments 2017 No. 1206, the Radio Equipment Regulations 2017

Delta Dore declares that the product is in conformity with the relevant statutory requirements applicable to the specific product.
The UK declaration of conformity for this equipment is available, on request, from: «Technical information» department DELTA DORE - 35270 BONNEMAIN (France) - e-mail: info.techniques@deltadore.com

European Directive RED 2014/53/UE (supersedes R&TTE 1999/5/CE)
Delta Dore hereby declares that the equipment complies with the essential requirements and other relevant provisions of the Directive RED 2014/53/UE. The EU declaration of conformity for this equipment is available, on request, from: «Technical information» department DELTA DORE - 35270 BONNEMAIN (France) e-mail: info.techniques@deltadore.com

Documents / Resources

References

• Google Play
• App Store - Apple

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download DELTA DORE Easy Bulb E27CW, E14CW, GU10CW - Smart LED Lamp Manual