3SIXT Fury Wireless Speaker Manual

Package Contains

Fury Speaker (3S-1647 – Black or 3S-1666 – Red)
USB-A to Micro USB Cable
Aux Cable
Operating Instructions

WARNINGS

• Read all instructions and warnings before using this product. Improper use of this product may result in product damage, excessive heat, toxic fumes, fire or explosion, for which damages you ("Purchaser") and not 3SIXT ("Manufacturer") are responsible.
• Do not store the accessory in a high-temperature environment, including heat caused by intense sunlight or other forms of heat (heaters etc.).
• Do not place the device in fire or other extremely hot environments.
• Do not disassemble or modify this accessory in any manner.
• Do not attempt to power this device using any other method than as instructed explicitly in this user guide.
• Be sure to unplug cables from the battery when not in use and departing your vehicle. Failure not to follow this warning is the sole responsibility of the purchaser, who agrees to indemnify the Manufacturer ("3SIXT").
• This accessory is intended for adults and not minors. Failure not to follow these warnings is the sole responsibility of the purchaser, who agrees to indemnify the Manufacturer ("3SIXT") for any unintended use/misuse by a minor.
• All products must pass through a thorough quality inspection at the time of manufacture. However, if you find that your device is excessively hot, is found to be deformed outside its regular appearance or is emitting smoke, immediately stop using the device and contact 3SIXT.

NAME PARTS

1. Power On/Off
2. Play/Pause/Answer Call/ Reject Call/Pair Mode
3. Mode Change/TWS Pair
4. Volume Down/Skip Back
5. Volume Up/Skip Forward
6. Port Cover
7. Mode Change/TWS Pair
8. Volume Up/Skip Forward
9. Play/Pause/Answer Call/ Reject Call
10. Volume Down/Skip Back
11. Lanyard Eye
12. Built-In Mic
13. Aux Port
14. TF Card Port
15. Micro USB Input
16. LED Ring

OPERATION

Charging up your Fury Speaker

1. Locate the provided USB-A to Micro USB Cable.
2. Locate the Micro USB input () on the Fury Speaker.
3. Make sure that the Micro USB input () is clear of obstruction (dirt/dust etc).
4. Plug the USB-A end of the cable into your BYO wall or car charger making sure to lightly push it in (do not push with excessive force).
5. Plug the Micro USB end into the Fury Speaker's Micro USB input () and push home making sure it is connected (do not push with excessive force).
6. Turn power on at the power source. The device LED Ring () will light up and breathe in a red colour. A solid green LED will then remain when fully charged, indicating the Fury Speaker is ready to be used.
7. To stop charging simply remove your cable from the Fury Speaker () or wall charger and replace the Port Cover ().
8. If the Fury Speaker sits idle charging and not playing music, it will automatically turn itself off to conserve power after 15 minutes.

Powering On

1. Locate the Power On/Off button on the underside of the Fury Speaker ().
2. Press and hold the Power On/Off button () for 2 seconds to turn on.
3. The Fury Speaker will make an audible sound and immediately activate pairing mode. The LED Ring () will flash blue On/Off in second intervals.

Powering Off

1. Locate the Power On/Off button on the underside of the Fury Speaker ().
2. Press and hold the Power On/Off button () for 2 seconds to turn off.
3. The Fury Speaker will make an audible sound and shut down.

Pairing (first time)

1. Follow 'Powering On' directions from step 1 to 3.
2. Locate your Bluetooth settings menu on your device and make sure it is on. Search for 'FURY SPEAKER'.
3. Once located select the Fury Speaker and auto pairing should occur. If prompted for a password, input "0000".
4. If successfully paired the Fury Speaker will make an audible sound and the LED Ring () will show as slow breathing blue

Unpairing

1. Locate your Bluetooth settings menu on your device and search for 'FURY SPEAKER'.
2. Select the Fury Speaker.
3. Locate the settings or information setting within that device and select "unpair or forget this device".
4. The Fury Speaker will make an audible sound to indicate it has unpaired and will resume pairing mode with the LED Ring () flashing 1 second On/Off.

TWS Pairing

1. Two Fury Speakers are required for this function.
2. Make sure to unpair your device/s from the Fury Speakers.
3. Power on both Fury Speakers () simultaneously.
4. On either of the Fury Speakers press and hold the Mode/TWS Pair button ( or ) to activate the TWS pairing function.
5. The Fury Speaker will make an audible sound to indicate it is in TWS pair mode.
6. When successfully paired to both Fury Speaker's one will make an audible sound.
7. Normal operation can now commence in stereo sound!

FM Radio

1. Follow 'Powering On' directions from step 1 to 2.
2. Locate "Mode Change/TWS Pair" button ( or ) and press once.
3. FM function will commence, and you will normally hear usual radio static.
4. Press and hold the Play/Pause button ( or ) to automatically cycle through all available stations on the FM band. This may take several minutes then once completed it will settle on a single FM station.
5. Once the auto-cycle has finished use "Skip Forward & Skip Back" buttons () to skip to a new station.
6. Add the included aux cable to act as antenna and better your FM experience.

SPECIFICATIONS

Item: 3S-1647 & 3S-1666

www.3sixtgear.com
or visit www.3sixtgear.com/support

3SIXTgear

© 2019 3SIXT. All rights reserved.

This product may be covered by one or more patents or pending patent applications. Designed in Australia by 3SIXT. 23/136 Keys Road, Cheltenham
VIC 3192 Australia
USB & the USB Logo are trademarks or registered trademarks of the USB Implementers Forum, Inc. in the United States and other countries.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc.

MADE IN CHINA

LIABILITY NOTICE

We reserve the right to printing errors and changes to product, packaging or product documentation.

• See our terms of the warranty. These are available in their current form by the importer of record in each region where the item is sold.

DISPOSAL

Parts of this unit contain materials that are recyclable. Certain waste companies specialise in recycling these parts. Dispose of the components in compliance with all applicable regions regulations.

EU DECLARATION OF CONFORMITY

With the CE sign, 3SIXT, an imported brand of Wentronic GmbH ensures, that the product is conformed to the basic European standards and directives.

AUSTRALIA & NEW ZEALAND TWO YEAR WARRANTY

The warranty does not extend to any consequential damages or costs that may be incurred and is valid for TWO YEARS from date of purchase. The warranty is provided by: Cellnet Limited (in Australia): 59-61 Qantas Drive, Eagle Farm, Queensland 4009. Ph: 1300 CELLNET (1300 235 563). Email: info@cellnet.com.au. Cellnet Limited (in New Zealand): 10a Orbit Drive, Rosedale, Auckland 0632. Ph: 0800 CELLNET (0800 235 563), Email: info@cellnet.co.nz

EUROPE WARRANTY

This warranty is by Wentronic GmbH. Wentronic GmbH offer the manufacturer's warranty in addition to the legal guarantee of this 3SIXT product. The warranty is provided by: Wentronic GmbH: Pillmannstraße 12, 38112 Braunschweig, Hotline: +49 (0531) 210 58-0 (0.14€ per minute within Germany. Max 0.42€ per minute from mobiles), Email: office@wentronic.de, Web: www.wentronic.de

For more detailed warranty information, please visit: www.3sixtgear.com/warranty-policy

Documents / Resources

References

• 3sixT Gear
• Returns and exchanges– 3sixT Gear
• Wentronic
• Warranty information– 3sixT Gear

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download 3SIXT Fury Wireless Speaker Manual