Product application Dual pressure switches monitor system pressure with two switch outputs and one analog output. danger This switch can only be used in the specified application range. The temperature range must be within the permissible range. Do not exceed the rated pressure and power load value.Assembly, commissioning and operation must be carried out in accordance with applicable national and local safety instructions.The switch is designed to be used as a safety device for pressurizing the system in accordance with...
Safety instruction Safety instructions are intended to protect users from dangerous situations and/ or prevent material damage.In the operating instructions, the severity of the potential risk can be indicated by the following signal words: danger An imminent danger to the user. Failure to comply may result in fatal injury. warning An identifiable hazard.
Principle structure The diffused silicon sensor is used for pressure measurement, and the signal is processed by a post-processing circuit and converted into a standard industrial electrical signal for output and display. The all-metal casing design, with a highlighted LED digital display, enables the product line to be used in a variety of industrial applications.
Page 5
Install Safety instructions are intended to protect users from dangerous situations and/or prevent material damage. In the operating instructions, the severity of the potential risk can be indicated by the following signal words: caution Vibration and violent vibration must be avoided during transportation. Even if the switch housing is not damaged, Internal components can also break down and cause failure.
factory data reset Hold down [+] to restore factory Settings Pressure value switch 1 signal: (Factory default HNO) Electrical connection Hysteresis function: HNO (normally open) /HNC (normally closed) Window function: FNO (normally open) /FNC (normally closed) ! Wiring must be done by a qualified electrician and the national and international codes for the installation of electrical equipment must be followed.
Page 8
Two way switch + one analog NPN(+Analog quantity) PNP(+Analog quantity) brown 12~30VDC 12~30VDC brown white white black black grey grey blue blue One switch + one analog NPN(+Analog quantity) PNP(+Analog quantity) 12~30VDC brown brown 12~30VDC black black white white blue blue Debugging/operation The pressure switch can only be debugged and operated by authorized personnel.
Page 9
Level 1 menu Alarm value of Switch 1 (Factory default value is 0.2% of the range) Hold down [+] or [-] for at least 1s. After 1 second: The setting value can be changed: At the press of a button, the value increases; Hold the button down and the value will keep changing.
Page 10
Level 2 menu factory data reset Hold down [+] to restore factory Settings Pressure value switch 1 signal: (Factory default HNO) Hysteresis function: HNO (normally open) /HNC (normally closed) Window function: FNO (normally open) /FNC (normally closed) Hold down [+] or [-] for at least 1s. After 1 second: The setting value can be changed: At the press of a button, the value increases;...
Page 11
OUT1 shutdown delay. (The factory default is 0s) Hold + or [-] for at least 1s. After 1 second: The setting value can be changed: At the press of a button, the value increases; Hold the button down and the value will keep changing. OUT2's opening delay.
Page 12
Update rate and direction of the display (d1 by default) Hold down [+] or [-] for at least 1s. After 1 second: The setting value can be changed: At the press of a button, the value increases; If you hold the button down, the value will keep changing. [d1] : The measured value is updated every 10ms [d2] : The measurement is updated every 100ms [d3] : Update measurement every 600ms...
Page 13
Display menu Level 1 menu The one-circuit switch does not have this function Level 2 menu Display menu www.katusensor.com...
Page 14
No analog model does not have this function Level 2 menu Display menu www.katusensor.com...
Hold down [+] or [-] for at least 1s. After 1 second: The setting value can be changed: At the press of a button, the value increases; Hold the button down and the value will keep changing. Switch point damping/process data flow (IO-Link communication) and display. (Factory default: 0.06) Maintenance/cleaning Hold down [+] or [-] for at least 1s.
Page 16
Katu Electronic (Kunshan)Co.,Ltd. The phone number is 400-150-8815 Website: www.katusensor.com Factory: No.1120 Jinyang East Road, Kunshan City, Suzhou City...