Table of Contents
Advertisement
Quick Links
INSTRUCTION, USE AND
MAINTENANCE HAND - BOOK
Machine: POLYMERIZING UNIT
Type: PL.06.00 – PL.12.00
O.M.E.C Snc di R. CARNEVALE & C. - Via dell'Artigianato 3/5/7 - I-20835 Muggiò (MB) - ITALY
Tel. +39-039-793740 Fax +39-039-2780689
E-Mail
export@omec-snc.com
-
omecsnc@libero.it
- Web site
www.omecitalia.com
Advertisement
Table of Contents
Summary of Contents for Omec PL.06.00
- Page 1 INSTRUCTION, USE AND MAINTENANCE HAND - BOOK Machine: POLYMERIZING UNIT Type: PL.06.00 – PL.12.00 O.M.E.C Snc di R. CARNEVALE & C. - Via dell’Artigianato 3/5/7 - I-20835 Muggiò (MB) - ITALY Tel. +39-039-793740 Fax +39-039-2780689 E-Mail export@omec-snc.com omecsnc@libero.it - Web site...
- Page 2 I N D E X SIDE I WARNINGS, PRECAUTIONS AND GENERAL ADVICES Page No. 1.1.1 Warnings 1.1.2 Precautions 1.1.3 General advice SIDE II PRODUCT DESCRIPTION 2.1.1 General features SIDE III ASSEMBLING, INSTALLATION AND USE INSTRUCTIONS 3.1.1 Installation 3.2.1 Picture No. 1 3.2.2 Picture No.
-
Page 3: Product Description
(due to bad carrying). b) Follow carefully the instructions for installing the machine. c) The OMEC POLYMERIZING UNIT TYPE PL.06.00 - PL.12.00 must be used only by a skilled worker, and therefore use the machine ONLY AFTER HAVING READ CAREFULLY and understood the instruction and maintenance hand-book. -
Page 4: Installation
It is possible to program only the boiling phase by setting 0°C as preheating temperature (phase no. 1). For boiling it is necessary to set FULL as boiling temperature (phase 2). If the boiling temperature is set on FULL, the rising speed is automatically set on FULL. The rising speed values do not correspond to °C/min but they refer to numbers of a scale where the max. - Page 5 Data display Orange led – Activated heating element Cycle programming key Cycle start up programming key / In progress cycle stop key Flashing red led = in progress program Still red led = in progress deferred start up timer Orange led = rising to programmed temperature Green led = in progress holding time Value increasing key Value decreasing key...
- Page 6 PROGRAMMING OF PREHEATING (PHASE NO. 1) Press key to program. The words “Ph.1”, “°C” and the last programmed preheating temperature value will appear in sequence on the display. The red led of key will start flashing intermittently during all preheating programming. The change f this parameter (programming range 0/100°C) is done by using key (to increase value) and...
- Page 7 For a rapid change the operator has to keep one of the two keys ( ) pushed for a time longer than 2 seconds. In this case the change of parameter will be by 10 steps correspondent to a 10 minutes a second until the release of the key. In the case a value equal to 00.00 is set, the time of preheating is not included and the polymerizing unit will pass directly to phase no.
-
Page 8: Start Up Programming
By keeping pushed one of the two keys ( ) for a time shorter than 2 seconds, the change of parameter will be by one step corresponding to 1 hour a press. For a rapid change the operator has to keep one of the two keys ( ) pushed for a time longer than 2 seconds. -
Page 9: Working Cycle
By keeping pushed one of the two keys ( ) for a time shorter than 2 seconds, the change of parameter will be by one step corresponding to 1 minute a press. For a rapid change the operator has to keep one of the two keys ( ) pushed for a time longer than 2 seconds. -
Page 10: Power Failures
Phases no. 1 and no. 2 During phases no. 1 and no. 2 the following inspections are possible by pressing the indicated key: : by keeping this key pressed you can see the temperature set for the running phase on the display. - Page 11 Before using cleaning techniques different from the ones indicated by OMEC Snc, the operator must contact the manufacturing company. Do not place any objects over the electrical cable and do not put cable in places where it can be stepped over.
Need help?
Do you have a question about the PL.06.00 and is the answer not in the manual?
Questions and answers