Subscribe to Our Youtube Channel
Summary of Contents for Total Source HFTE0007
- Page 1 Original operating manual OPERATING MANUAL ELECTRIC LIFT TABLE H F T E 0 0 0 7 - H F T E 0 0 3 3 12/2021 – V01 from serial n° M202007152...
- Page 2 © 12-2021. TVH and TotalSource are registered trademarks. TVH Parts Holding NV, Brabantstraat 15, B-8790 Waregem. All rights reserved. ® ® No part of this publication may be reproduced or communicated in any form or by any means, electronic or mechanical, including copying, recording or use in an information storage or retrieval system, without prior and explicit permission of TVH Parts Holding NV.
- Page 3 Manuál vo vašom jazyku môžete nájst v priloženom vysvietenom riadku. Slovenian Ta priročnik najdete v svojem jeziku preko spodnje povezave. Swedish Du kan hitta denna manual på ditt språk via länken nedan. Turkish Bu kılavuzu aşağıdaki bağlantıdan kendi dilinizde bulabilirsiniz. https://www.tvh.com/hfte0007-hfte0033-rv01 3/36...
- Page 4 Thank you for using our product. For your safety and to ensure a correct operation, we would like to bring to your attention some aspects of this manual: • This booklet supplies useful instructions for the correct operation and maintenance of the product.
-
Page 5: Table Of Contents
................5.5. Installation of the product (models HFTE0007 – HFTE0033) ....... -
Page 6: Introduction
INTRODUCTION This lift table is an electrically operated lift table. It is designed to lift and lower loads. The lift table should be used on hard and even surfaces, indoor and in dry conditions. Suitable ambient temperature is −15 °C up to 60 °C. We guarantee a long period of trouble free operation if the unit is operated and maintained correctly. -
Page 7: Description
DESCRIPTION 2.1. Technical data Always check the type plate for the correct information. Single scissor Type HFTE0007 HFTE0008 HFTE0009 HFTE0010 HFTE0011 Load capacity (kg) 1000 1000 1000 1000 1000 Maximum height (mm) (H2) 1000 1000 1300 1300 1300 Minimum height (mm) (H3) - Page 8 Type HFTE0022 HFTE0023 HFTE0024 HFTE0025 HFTE0026 Load capacity (kg) 4000 4000 4000 4000 4000 Maximum height (mm) (H2) 1400 1400 1400 1400 1400 Minimum height (mm) (H3) Length of the platform (L2) (mm) 2000 2200 2200 1700 2200 Width of the platform (W2) (mm) 1200 1000 1200...
- Page 9 Quadruple scissor Type HFTE0032 HFTE0033 Load capacity (kg) Maximum height (mm) (H2) 4140 4210 Minimum height (mm) (H3) Length of the platform (L2) (mm) 1000 1000 Width of the platform (W2) (mm) 1700 1700 Material of the lift table Steel Steel Voltage (V) - phase 380 - 3...
-
Page 10: Main Components Of The Product
2.2. Main components of the product N° Component Platform Remote controller Anti-crush system Motor Electric plug Fixed side Scissor mechanism Oil reservoir Safety mechanism 10 Rollers/moving side 11 Hydraulic pump 12 Holes for ring bolts 13 Lowering switch 14 Lifting switch 15 Emergency switch 2.3. -
Page 11: Type Plate
2.4. Type plate N° Type plate Explanation Type of lift table Serial number Capacity of the lift table Weight of the lift table Type lifting table xxxxxx Lifting height xxx mm Serial n° xxxxxx Length of the platform xxx mm Name and address of the Capacity xxx kg... -
Page 12: Safety Instructions
SAFETY INSTRUCTIONS 3.1. Explanation of the safety decals If the decals are damaged or missing, please replace them. N° Decal Explanation Reference Maximum load capacity:1000 kg 166TA7294 Maximum load capacity: 400 kg 166TA7575 Maximum load capacity: 800 kg 166TA7576 Maximum load capacity: 2000 kg 166TA7295 Maximum load capacity: 4000 kg 166TA7296... -
Page 13: General Safety Instructions
3.2. General safety instructions • The operator should read all warning signs and instructions in the manual and on the lift table before using it. • Do not operate a lift table unless you have been trained or authorised to do so. •... -
Page 14: Transport And Storage
TRANSPORT AND STORAGE The lift table must be lowered completely when it is not in use. When not in use, the lift table can be stored horizontally on a pallet. To do this, follow the next steps: Bring the lift table to the lowest position. Disconnect the electric plug. - Page 15 Move the pallet with a pallet truck or lift truck. The lift table must always be stored in a dry environment. If the lift table will be stored for more than one month, lubricate all necessary parts (see chapter 7). If necessary, the lift table can be transported with a lift truck using the attached ring bolts, or on a pallet.
-
Page 16: Assembly And Installation
To secure the lift table to the ground or to install it into a pit, carefully read the next topic. 5.5. Installation of the product (models HFTE0007 – HFTE0033) If the lift table is going to be installed in a pit, these are the requirements for the pit: •... - Page 17 Make sure the pit is clean and there is no water or other fluids in it that can damage the electrical system of the lift table. Make sure that the flooring is flat and that it can support the lift table and its capacity. To attach the lift table to the ground, follow the next steps: Mark the location of the pre-drilled mounting holes on the floor.
-
Page 18: Operation
OPERATION 6.1. Safety instructions for operating the product • A damaged or malfunctioning product must never be used. If damage or malfunctions are discovered during pre-operation inspection or function tests, the product must be tagged and removed from service. • The operator may not wear any loose objects, such as necklaces, rings, scarves … as they may become entangled in the product and thus cause harm to the operator. -
Page 19: Operating Instructions
6.2. Operating instructions Please see chapter 7 for the daily maintenance schedule. N° Component Lowering switch Lifting switch Emergency switch 1. Lifting button When pressing this button, the lift table will lift until you release the button. 2. Lowering button When pressing this button, the lift table will lower until you release the button. 3. - Page 20 5. Loading and unloading the lifting table Check if the load capacity of the lifting table is sufficient for the load you want to lift . Lift or lower the lifting table to the desired position by using the lifting button or lowering button.
- Page 21 If the work is finished remove the load from the lift table. When the lift table is not in use, it must be lowered completely. 21/36...
-
Page 22: Maintenance
MAINTENANCE 7.1. Safety instructions for the repair of the product • Always do maintenance and routine check while the lift table is unloaded. • Before servicing the lift table, make sure to turn off the power supply. • After servicing it is necessary to check the function of the lift table again. •... -
Page 23: Maintenance Instructions
7.3. Maintenance instructions 1. Daily maintenance check A daily maintenance check of the lift table can limit wear to a minimum: • Check the axles for blockages. • Check if there are any damaged or loose bolts, nuts or cotter pins. •... - Page 24 3. Check hydraulic oil Please check the oil level every six months. The oil capacity is about 1,5 l. Use the correct type of hydraulic oil. When determing oil levels, keep in mind that the tank contains the greatest amount of oil when the lift table is in its lowest position.
- Page 25 5. Fasten all the connection parts / check electrical system Fasten all the connection parts / check electrical system can only be done by a qualified service technician and according to the manufacturer’s instructions. • Fasten all the connection parts again •...
-
Page 26: Troubleshooting
TROUBLESHOOTING N° Problem Cause Action The lift table The level of hydraulic oil is too low Add hydraulic oil, see chapter 7 doesn’t reach The table is overloaded Remove excessive load, check type the maximum plate for the load capacity height The table can The level of hydraulic oil is too low Add hydraulic oil, see chapter 7... - Page 27 N° Problem Cause Action The lift table Impurities in the oil cause the release Replace the oil, see chapter 7 lowers without valve to be unable to close tight the release valve Sealing parts are worn or damaged Replace the seals, see spare parts list being operated The release valve is damaged Replace the release valve, see spare...
-
Page 28: Final Decommissioning And Disposal
FINAL DECOMMISSIONING AND DISPOSAL Final, proper decommissioning or disposal of the product must be performed in accordance with the regulations of the country in which the product is used. In particular, regulations governing the disposal of batteries, fuels and electronic and electrical systems must be observed. -
Page 29: Annexes
Merk / Marque / Brand / Marke / Marca TotalSource HFTE0007 / HFTE0008 / HFTE0009 / HFTE0010 / Type / Typ / Tipo HFTE0011 / HFTE0012 / HFTE0013 / HFTE0014 / HFTE0015 / HFTE0016 / HFTE0017 / HFTE0018 /... - Page 30 ORIGINAL DECLARATION ● dat de heftafel voldoet aan alle toepasselijke bepalingen van de hierna vermelde richtlijnen en geharmoniseerde normen; que le table élévatrice satisfait à l’ensemble des dispositions pertinentes des directives et normes harmonisées ci-dessous; that the lifting table fulfills all the relevant provisions of the directives and harmonized standards stated herein below;...
-
Page 31: 10.2. Electrical System
10.2. Electrical system 31/36... -
Page 32: 10.3. Hydraulic System
10.3. Hydraulic system 32/36... - Page 33 NOTES ........................
- Page 34 NOTES ........................
- Page 35 NOTES ........................
- Page 36 Your distributor: Manufactured outside the EU for: TVH PARTS HOLDING NV Brabantstraat 15 • 8790 Waregem • Belgium T +32 56 43 42 11 • F +32 56 43 44 88 • info@tvh.com • www.tvh.com...
Need help?
Do you have a question about the HFTE0007 and is the answer not in the manual?
Questions and answers