SAFETY INFORMATION Important - Please read these instructions fully before starting assembly. WARNING SYMBOLS Read the manual Warning Warning: Do not direct the jet at persons, animals and electrical equipment Machine not suitable for connection to the potable water mains Double insulation RCM marking ABN: Australian Business Number.
Page 4
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. - This machine is not intended for use by persons (including children) with reduced physical,sensory or mental capabilities, or lack of experience and knowledge.
Page 5
converting the machine to another function. - WARNING Do not use machine if a supply cord or important parts of the machine are damaged, e.g. safety devices, high pressure hoses, trigger gun. - WARNING If an extension cord is used, the plug and socket must be of watertight construction.
ACCESSORIES Spray gun Normal nozzle Pressure hose(3M) Soap bottle Spray gun holder Electric cable holder Inlet water connector Connection lance ASSEMBLY NOTE: Before using the tool, read the instruction book carefully. ASSEMBLY 1. Assembling spray gun holder Press the spray gun holder (2) on to the machine. (Fig. A) 2.
Page 9
3. Mounting of inlet water connector Attach inlet water connector (13) to the machine’s inlet. (Fig. C, D) 4. Mounting of adjustable spray nozzle and lance holder Place the adjustable spray nozzle and lance holder on to the machine, and fix the screws. (Fig.
Page 10
6. Assembling the high pressure hose 1) Make sure that on/off switch (3) is in off position. (Fig. G1) 2) Insert the high-pressure hose (14) to spray gun (1). (Fig. G2) 3) Insert the lance into spray gun (1), and twist 1/4 turn. Then insert the adjustable spray nozzle into the lance, and twist 1/4 turn until rectangular tab appears.
OPERATION INSTRUCTION Caution! 1. Never use the pressure washer to draw in water contaminated with solvents (e.g. paint thinners, gasoline, oil, etc.). 2. Dirt in the feed water will damage the unit. To avoid this risk, we recommended checking the water filter (located inside the water inlet; to clean it out see maintenance section). 3.
Page 13
2. USING THE ACCESSORIES 2.1 Adjustable wand The adjustable nozzle allows you to use any variety of spray patterns from a fan spray to a pencil jet spray. When using pressure washer to clean wood decks, siding, vehicles etc., always start using the fan spray and begin spraying from a minimum 36” away to avoid damaging the surface of the material you are cleaning.
Page 14
STORAGE The machine should be stored in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine and detach water hose and accessory. 2. Restart the machine and activate the trigger. Let the machine run until no more water runs through the spray gun (1).
MAINTENANCE WARNING! Always disconnect the electrical plug from the socket prior to maintenance or cleaning. To ensure a long and problem free working life, please take the following advice: - Wash out water hose, high pressure hose, spray lance and accessories before mounting. - Clean the connectors of dust and sand.
TROUBLESHOOTING Disconnect the machine from the power source before making any repair. To avoid unnecessary disappointments, you should check the following before contacting the service organization: Symptom Possible causes Solution Machine not plugged in Plug in machine Machine refuses Defective socket Try another socket.
TECHNICAL DATA 220-240V~50/60Hz Voltage Rated power 1400 W Rated pressure 7 MPa(1000 psi) Max Pressure 10.5 MPa(1500 psi) Rated water flow rate 5.5 l/min Maximum inlet water pressure 0.7 MPa(100 psi) Protection class Protection degree IPX5 Machine weight 4.5 kg Product dimensions 270*265*490 mm...
Page 18
NOISE Information A weighted sound pressure = 73.4 dB(A) A weighted sound power = 87.4 dB(A) Guaranteed sound power = 92 dB(A) &K 3.0 dB(A) Wear ear protection. VIBRATION INFORMATION = 0.979 m/s² (Main handle) = 1.020 m/s² (Auxiliary handle) Vibration emission value Uncertainty K = 3.0 m/s²...
WARRANTY Our product is guaranteed to be free from quality and manufacturing defects for a period of 12 months. If your product becomes defective during this period, SRGS PTY LTD will offer you either a replacement, credit or refund where a product is faulty; wrongly described; different from the sample shown to you or do not do what they are supposed to do.
Page 20
1400W 1500PSI HIGH PRESSURE WASHER INSTRUCTION MANUAL “If the product fails to perform as specified we’ll happily offer a refund or exchange” Manufactured & packaged for SRGS PTY LTD ABN 23 113 230 050 6 Coulthards Avenue Strathpine QLD 4500, Australia MADE IN CHINA...
Need help?
Do you have a question about the PLU 637450 and is the answer not in the manual?
Questions and answers