AU SAE J1939 User Manual
  1. Manuals
  2. Brands
  3. AU Manuals
  4. Switch
  5. SAE J1939
  6. User manual

AU SAE J1939 User Manual

Simulator gen ii 1.00a
Hide thumbs Also See for SAE J1939:
Table of Contents

Advertisement

Quick Links

Download this manual
Au Group Electronics
Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G
Au SAE J1939 Simulator Gen II 1.00A
User Manual
Rev. G
Au Group Electronics
May 2019
All Copyrights are reserved by Au Group Electronics. 2007 - 2019
Au Group Electronics
This document can
NOT
be freely distributed without written approval from
Website:
www.AuElectronics.com
1
Support:
Support@AuElectronics.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SAE J1939 and is the answer not in the manual?

Questions and answers

Related Manuals for AU SAE J1939

Summary of Contents for AU SAE J1939

  • Page 1 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Au Group Electronics May 2019 All Copyrights are reserved by Au Group Electronics. 2007 - 2019...

  • Page 2: Table Of Contents

    Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Table of Contents Table of Contents ............................2 Chapter 1 - Introduction ..........................3 1.1. Typical SAE J1939-15 Network Topology with Au SAE J1939 Simulator ......3 1.2. Major Hardware Features ......................3 1.3. Major Operating Features......................6 1.4.

  • Page 3: Chapter 1 - Introduction

    Power, Range, Warning, ▼0%, 20%, 40%, 60%, 80%,▲100% • 1 buzzer • 3 push buttons: simulated SAE J1939 signals can be adjusted by 3 push buttons: Menu, Down, Up • 1 DB9 Male "BUS" Interface: for power supply and CAN/J1939 network connection (Figure 1-3) •...
  • Page 4 PC with RS232 port Au J1939 Simulator plus edition can be connected to a PC through USB port using USB to RS232 serial convert cable (part # CBL-USB-232), as shown in Figure 1 - 6. Figure 1-6 Connection of Au J1939 Simulator (Gen II) plus editions to PC with USB port The following cables and power supply are optional components for different application, they are sold separately.
  • Page 5 A 6-wire color coded cable which can be used for Au J1939 devices and Au J1708 devices. One end of the cable is DB9 female connector; it is designed to mate with Au devices on BUS side. The other side of the cable is a pig tail with 3 pairs of twisted color coded wires: Red wire: Power supply, e.g.

  • Page 6: Major Operating Features

    The Plus editions have all the functions of Non-plus editions, plus a PC Remote Terminal GUI program, which can be used to control and display detail information of simulated SAE J1939 signal on PC screen (detail information is available at chapter 4.)

  • Page 7: License /Firmware Upgrade And Annual Support Service

    • Annually upgrade and support service is available at Au Group Electronics (part #: SVS-SIM-J1939). Part numbers for license upgrading and annual service for the 8 editions of Au SAE J1939 Simulator Gen II 1.00A are summarized in Figure 1-7.

  • Page 8: Chapter 2 - Supported Sae J1939 Parameters

    * Response only with SAE J1939-21 Request PGN 59904. 2.2. Engine Basic editions Au SAE J1939 Simulator Gen II 1.00A Engine Basic editions support all parameters listed with Value package editions, plus the following 20 SAE J1939 engine parameters (total 31): •...

  • Page 9: Chapter 3 - Operating Instructions

    In dynamic mode, the simulator automatically adjusts the control step value by itself. This will generate dynamic J1939 signals. In static mode, all* simulated SAE J1939 signal will be controlled by the control step value, which is still able to be manually controlled by the Up and Down buttons.

  • Page 10: Led Indicator Status

    Note: Red LEDs and Green LEDs are used in this document for illustration purpose; actual product might have different LED color. Same applies to the push buttons. Au Group Electronics reserve the right of changing the color on each LEDs and push buttons without further notification.
  • Page 11 Figure 3-2 Power on, both Power and Range LED lit All SAE J1939 data can be changed within the SAE defined range from 0 to 100 control steps (named 0% to 100% control step value from now on), 6 LEDs are used to identify the control step value in the range of 0%, 20%, 40%, 60%, 80%, and 100%.
  • Page 12 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Figure 3-6 Power, Range, 20%, 40%, 60%, 80% LED on, indicates data ranges from 81% to 99% When control step value equals to 100%, 20%, 40%, 60%, and 80% LED will be constant on. ▲100% LED blinks, as shown in Figure 3-7.

  • Page 13: Chapter 4 - Au J1939 Simulator Remote Terminal Gui

    Chapter 4 - Au J1939 Simulator Remote Terminal GUI For all Au SAE J1939 Simulator Gen II 1.00A “Plus” editions, the “Au J1939 Simulator Remote Terminal Ver. 1.00A” GUI can be used to control and display simulated SAE J1939 signals on PC screen.
  • Page 14 Figure 4-4 SIMJ1939 GUI - Engine Basic Plus Edition Figure 4 - 5 shows the Remote Terminal GUI for Au SAE J1939 Simulator Gen II 1.00A Value Package Plus edition, 6 most frequently used Engine Parameters are available: Website: www.AuElectronics.com...

  • Page 15: Control Panel - Step 1: Connect To J1939 Simulator

    Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Figure 4-5 SIMJ1939 GUI - Value Package Plus Edition Following paragraphs will explain how to use the GUI to remote control Au SAE J1939 Simulator Gen II 1.00A Plus editions.

  • Page 16: Control Panel - Step 2: Remote Control The J1939 Simulator

    Remote control includes 1 scale bar, 3 push buttons (Menu, Down, Up), and 4 check boxes (Dynamic, Quite, Warnings, Reset Eng DM2), as shown in Figure 4-7. These tools are able to remote control the output/simulated signal of the Au J1939...

  • Page 17: Display Panel - Transmission Info And Warning Lamps

    Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G 4.5. Display Panel – Transmission info and Warning Lamps It displays the transmission address claiming information, transmission oil temperature, and 2 warning lamps for transmission (Red Stop, Amber), as shown in Figure 4-10.
  • Page 18 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Detail data information of engine DM1 multi-packet is showing in Table 4 – 4 to 4 – 7. Table 4 – 4 Engine DM1 Multi-Packets (1 – 16) 1081 Table 4 –...

  • Page 19: Display Panel - Engine Dm2

    Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G 4.9. Display Panel – Engine DM2 Engine DM2 message could be a single packet or multi-packet. If engine DM2 is a single packet, SPN, FMI, OC, CM will display (Figure 4-16).

  • Page 20: Display Panel - Engine Configuration

    Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G 4.10. Display Panel – Engine Configuration Engine Configuration PGN includes 39 bytes of messages, which require transport protocol for multi-packet communication. “Engine Configuration” button will be active on the remote terminal GUI for Vehicle Platinum editions, as shown in Figure 4 - 19.

  • Page 21: Chapter 5 - Data Configuration

    Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Chapter 5 - Data Configuration Table 5-1 listed simulated result at control step value of 0%, 20%, 40%, 60%, 80%, and 100%. J1939 Parameters 100% RPM (rpm) 1606.38...
  • Page 22 Fuel Level (96) 65279 Water in Fuel Indicator (WFI) Water In Fuel Indicator (97) As defined by SAE J1939-21, Au SAE J1939 simulator response to different “engine DM2 request” with different transport protocols (illustrated in Table 5-4). Website: www.AuElectronics.com Support: Support@AuElectronics.com...
  • Page 23 TP.CM.Abort The simulation result vs. control step value (from 0 to 100) is illustrated in Table 5-5 to Table 5-14. Table 5 – 5 SAE J1939 Simulation result vs. control step values (from 1 to 10) Control Step RPM (rpm) 0.00...
  • Page 24 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Table 5 – 7 SAE J1939 Simulation result vs. control step values (from 21 to 30) Control Step RPM (rpm) 1686.63 1767.00 1847.25 1927.63 2007.88 2088.25 2168.50...
  • Page 25 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Table 5 – 9 SAE J1939 Simulation result vs. control step values (from 41 to 50) Control Step RPM (rpm) 3293.00 3373.38 3453.63 3534.00 3614.25 3694.63 3774.88...
  • Page 26 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Table 5 – 11 SAE J1939 Simulation result vs. control step values (from 61 to 70) Control Step RPM (rpm) 4899.38 4979.75 5060.00 5140.38 5220.63 5301.00 5381.25...
  • Page 27 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Table 5 – 13 SAE J1939 Simulation result vs. control step values (from 81 to 90) Control Step RPM (rpm) 6505.75 6586.13 6666.38 6746.75 6827.00 6907.38 6987.63...

  • Page 28: Appendix A - Remote Terminal Gui Installation Guide

    Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G Appendix A - Remote Terminal GUI Installation Guide A remote terminal program can be used to control and display detail information of simulated SAE J1939 signals on a PC screen.
  • Page 29 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G 5. “Select Destination Location” window pop up, use the default folder, and click “Next” to continue (Figure A-5). 6. “Select Start Menu Folder” window pop up, use the default folder and click “Next” to continue (Figure A-6).

  • Page 30: Appendix B - Can Baud Rate Configuration

    Appendix B - CAN Baud Rate Configuration Au J1939 Simulator can be configured to the following 5 baud rate: 62.5K bps, 125K bps, 250K bps, 500K bps, 1M bps. The default factory setting of Au J1939 Simulator CAN Baud Rate is 250K bps. The following example illustrate on how to change the default CAN baud rate from 250K bps to 500K bps.

  • Page 31: Appendix C - License Management Toolset

    1. Order new license code from the following web link: http://www.auelectronics.com/System-J1939Simulator.htm 2. PC software: “AU J1939 Simulator License Management Toolset V2.00A” is included in the software disc when any Au J1939 Simulator is ordered. 3. A PC equipped with serial port and a serial extension cable or a PC equipped with USB port and a "USB to Serial Converter".
  • Page 32 “Ready to Install” window shows up, click “Install”, as shown in Figure C-7. Figure C-6 Figure C-7 Wait until “Completing Au J1939 Simulator License Management Toolset Setup Wizard” window shows up, check “launch Au J1939 Simulator License Management Toolset”, then click “Finish” (Figure C-8, Figure C- Figure C-8 Figure C-9 Website: www.AuElectronics.com...
  • Page 33 Figure C-11 3. Au J1939 Simulator License Toolset will check if entered license number is valid or not. If not, “the license is not for this product” message window will show up, click OK, “Sorry, Invalidate license!” then show up, click OK, (Figure C-12.
  • Page 34 Engine premium license validate 5. When it is updated successfully, a beep will be heard. And Au J1939 Simulator License Toolset will show the new license (Engine premium in this demonstration), it means your product has been upgraded to engine premium edition successfully, click “Exit”, as shown in Figure C-14.

  • Page 35: Appendix D - Au Pic Serial Bootloader Application Note

    Note: If the Au PIC Bootloader has been installed on PC before, please bypass step 1 to step 8, and start with step 1. Double click icon of the “Setup Au PIC Bootloader V1.00B” to start installing Au PIC Bootloader (Figure D-1).
  • Page 36 Au Group Electronics Au SAE J1939 Simulator Gen II 1.00A User Manual Rev. G 5. “Select Start Menu Folder” window show up, use default setting “AU PIC Bootloader”, then click “next” (Figure D-5). “Select Additional Task” window shows up, check both “create a desktop icon” and “Create a quick launch icon”, and then click “next”...

This manual is also suitable for:

Simj1939-013Simj1939-001Simj1939-002Simj1939-003Simj1939-014Simj1939-004 ... Show all

Table of Contents