Advertisement
2. INTRODUCTION & SPECIFICATION
Features tilt and swivel head for optimum air circulation. Push-button controls and fully guarded fan blades to Bs5060/IEc879 for ease of use
and extra safety. smooth running motor powers both fan blades and oscillating gearbox for even air distribution.
Fan Diameter:. . . . . . . . . . . . . . . 400mm(16")
speeds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. ASSEMBLY
unpack carton and assemble the fan as follows:
3.1.
Fix pole to base using four screws and slide base cover over pole.
3.2.
Fit head unit onto top of pole and secure by tightening knob at base of head.
3.3.
unscrew and remove the large plastic locking cap from the motor spindle of the fan (Note: left-hand thread). then unscrew and
remove the plastic locking ring (Fig.1.1) from the motor housing.
3.4.
Fitting the rear fan guard.
Identify the rear fan guard by the location holes in the centre plate (Fig.1.2) and place the guard over the fan spindle and fit onto the
three location pins (Fig.1.3).
3.5.
secure the rear guard with the plastic locking ring (Fig.1.1).
3.6.
Fitting the blade.
slide the blade onto the motor spindle until it comes to rest against the pin, ensure the pin engages with the cutouts on the blade.
thread the large plastic locking cap onto the end of the motor spindle by turning it anticlockwise. Hold one of the blades and tighten
the cap down onto the blade.
3.7.
Fitting the front fan guard to the rear fan guard.
Hook the clip on the top of the front guard (Fig.2.A) over the rear guard and fit and tighten the screw and nut at the bottom of the
guards (Fig.2.B). slide the four other clips on the front guard down to secure the guards together.
3.8.
check that the guard has been assembled correctly and that the fan will turn freely before plugging into the mains power supply.
the fan is now ready to use.
4. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions
in part 1 before using the fan.
4.1.
Place the fan in a suitable location on level ground. Plug into the mains power
supply.
4.2.
Adjust tilt, direction and height of fan as required.
4.3.
Press one of the three speed buttons (1,2 or 3) to switch the fan on.
4.4.
speed is simply altered by pressing the desired button.
4.5.
to make the fan oscillate, press down the oscillating button on top of the fan.
to stop the fan oscillating, pull the button up.
4.6.
When the fan is no longer required, press the "0" button to switch it off.
4.7.
If not required again for some time, unplug from mains and store away in a
safe, dry, childproof location. cover the fan to protect it from dust.
5. CARE OF FAN
IMPortAnt: turn the fan oFF and disconnect from power supply before cleaning.
5.1.
use only a soft, damp cloth to clean the fan.
5.2.
Do not submerse the fan in water and nEVEr allow water to drip into the
motor housing.
5.3.
Do not use solvents or other chemicals to clean the fan.
5.4.
to clean the fan blades, remove front guard - reverse of assembly procedure
3.7. above.
5.5.
Wipe the blades and guards clean.
5.6.
reassemble front guard following assembly procedure 3.7. and 3.8. above.
5.7.
store the fan in its original box or otherwise cover the fan to protect it from
dust.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
Maximum Air Flow: . . . . . . . . . . . . 68mtr³/min
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . 40W
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. Edmunds, suffolk,
IP32 7Ar
Original Language Version
Input:. . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
overall Height: . . . . . . . . . . . . 1090-1390mm
www.sealey.co.uk
01284 757500
Web
sales@sealey.co.uk
01284 703534
email
sPF16W
Fig.1
Fig.2
Issue: 2 - 19/04/10
Advertisement
