Pioneer MVH-MS310BT - Marine Digital Media Receiver Quick Start Guide
![]()
![]()
(Serial number)
The serial number is located on the bottom of this unit. Be sure to record this number on the enclosed warranty card before the unit is installed.
If your boat's ignition has no ACC position, some settings are not saved to the memory. To save, detach the front panel or wait for the unit to shut off completely for 10 seconds after turning it off by pressing and holding SRC/OFF (when [ON] is selected in [PW SAVE]), then turn the ignition off.
This guide is intended to guide you through the basic functions of this unit. For details, please refer to this product's Operation Manual, which you can look up here: https://www.pioneerelectronics.com/PUSA/Support
See Operation Manual for instructions to turn off demonstration display (DEMO OFF).
Before You Start
To ensure proper use, please read through this guide and the Operation Manual before using this product. It is especially important that you read and observe WARNINGS and CAUTIONS in this guide. Please keep the guide in a safe and accessible place for future reference.
The Safety of Your Ears is in Your Hands
Get the most out of your equipment by playing it at a safe level—a level that lets the sound come through clearly without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Sound can be deceiving.
Over time, your hearing "comfort level" adapts to higher volumes of sound, so what sounds "normal" can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts.
ESTABLISH A SAFE LEVEL:
- Set your volume control at a low setting.
- Slowly increase the sound until you can hear it comfortably and clearly, without distortion.
- Once you have established a comfortable sound level, set the dial and leave it there.
BE SURE TO OBSERVE THE FOLLOWING GUIDELINES:
- Do not turn up the volume so high that you can't hear what's around you.
- Use caution or temporarily discontinue use in potentially hazardous situations.
- Do not use headphones while operating a motorized boat; the use of headphones may create a traffic hazard and is illegal in many areas.
![]()
- Do not attempt to install or service this product by yourself. Installation or servicing of this product by persons without training and experience in electronic equipment and automotive accessories may be dangerous and could expose you to the risk of electric shock, injury or other hazards.
- Do not attempt to operate the unit while operating the boat. Make sure to stop the boat in a safe location before attempting to use the controls on the device.
- Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result. Also, damage to this unit, smoke, and overheating could result from contact with liquids.
![]()
- Allow the unit to cool down before using it if your boat has been docked in direct sunlight.
- Do not leave the detachable front panel sitting in direct sunlight, which may cause malfunction due to overheating.
- Using this unit after your hands have touched sea water may cause rust or malfunction. Please wash your hands thoroughly with clean water before use.
- Always keep the volume low enough to hear outside sounds.
- This product is evaluated in moderate and tropical climate condition under the Audio, video and similar electronic apparatus - Safety requirements, IEC 60065.
After-sales service for Pioneer products
Please contact the authorized Pioneer dealer from which you purchased this unit or an authorized Pioneer service company for after-sales service or questions you may have about the product.
You may contact Pioneer directly as follows:
Do not ship your unit in for repair without contacting Pioneer first. Units sent without a return authorization number will be refused.
In the U.S.A. and CANADA:
Pioneer Electronics (USA) Inc.
CUSTOMER SUPPORT DIVISION
P.O. Box 1760
Long Beach, CA 90801-1760
800-421-1404
https://www.pioneerelectronics.com/
PUSA/AboutPioneer/Contact+Us
For warranty information please see the Limited Warranty sheet included with this unit.
Connections
![]()
- If your boat's ignition has no ACC position: Be sure to set [PW SAVE] to [ON] (for details, refer to the Operation Manual). The unit will automatically shut off completely after the unit is turned off to prevent battery drain. Otherwise, press and hold SRC/OFF until the display turns off each time you turn the ignition off.
- When using 4 channel speaker output, use speakers rated 50 W (maximum input power) or higher and between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω to 3 Ω speakers with this unit regardless of the number of channels.
- When using a 2 Ω subwoofer with the rear speaker output, use speakers rated 70 W or higher.
* Please refer to connections for a connection method. - The black cable is ground. When installing this unit or power amp (sold separately), make sure to connect the ground wire first. Ensure that the ground wire is properly connected to a metal part of the boat's body. The ground wires of a power amp, this unit, and any other devices must each be connected to the boat separately with different screws. If the screw for the ground wire loosens or falls out, it could result in fire, generation of smoke or malfunction.
Two devices connected to the boat separately (ground wires)
![Pioneer - MVH-MS310BT - Two devices connected to the boat separately Two devices connected to the boat separately]()
*1 Not supplied for this unit
![]()
![]()
- When this unit is installed in a boat without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.
![]()
![]()
- Use this unit with a 12-volt battery and negative grounding only. Failure to do so may result in a fire or malfunction.
- To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below.
- Disconnect the negative terminal of the battery before installation.
- Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.
- Place all cables away from moving parts, such as the shift lever and seat rails.
- Place all cables away from hot places, such as near the heater outlet.
- Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment.
- Cover any disconnected cable connectors with insulating tape.
- Do not shorten any cables.
- Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited.
- Use a fuse of the rating prescribed.
- Never wire the negative speaker cable directly to ground.
- Never band together negative cables of multiple speakers.
- When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an external power amp or the boat's auto-antenna relay control terminal (max. 300 mA 12 V DC). If the boat is equipped with a glass antenna, connect it to the antenna booster power supply terminal.
- Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.
- The graphical symbol
placed on the product means direct current.
This unit
![Pioneer - MVH-MS310BT - Unit Connections Unit Connections]()
- Power cord input
- Microphone input
- Microphone 3 m (9 ft. 10-1/8 in.) (not waterproof)
- Rear output or subwoofer output
- Front output
- Antenna input
- Fuse (10 A)
- Wired remote input
Pioneer marine wired remote control (CD-ME300) can only be connected (sold separately).
Power cord
Perform these connections when not connecting a rear speaker lead to a subwoofer.
![Pioneer - MVH-MS310BT - Power cord connection without subwoofer Power cord connection without subwoofer]()
Perform these connections when using a subwoofer without the optional amplifier.
![Pioneer - MVH-MS310BT - Power cord connection with subwoofer Power cord connection with subwoofer]()
![]()
![]()
In the above case, two 4 Ω subwoofers wired in parallel will represent a 2 Ω load.
- To power cord input
- Left
- Right
- Front speaker
- Rear speaker
- White
- White/black
- Gray
- Gray/black
- Green
- Green/black
- Violet
- Violet/black
- Black (chassis ground)
Connect to a common ground point. - Yellow
Connect to the constant 12 V supply terminal. - Red
Connect to terminal controlled by the ignition switch (12 V DC). - Blue/white
Connect to the system control terminal of the power amp or auto-antenna relay control terminal (max. 300 mA 12 V DC). - Subwoofer (4 Ω)
- When using a subwoofer of 2 Ω, be sure to connect the subwoofer to the violet and violet/ black leads of this unit. Do not connect anything to the green and green/black leads.
- Not used.
- Subwoofer (4 Ω) × 2
Power amp (sold separately)
Perform these connections when using an optional amplifier.
![Pioneer - MVH-MS310BT - Power amp connections Power amp connections]()
- System remote control Connect to blue/white cable.
- Power amp (sold separately)
- Connect with RCA cables (sold separately)
- To front output
- Front speaker
- To rear output or subwoofer output
- Rear speaker or subwoofer
Installation
![]()
To customer:
This product includes a radio transmitter. According to UNECE Regulation no. 10, vessel manufacturers may impose specific conditions for the installation of radio transmitters into boats. Please check your boat's operation manual or contact the manufacturer or your boat dealer before you install this unit.
![]()
- Carefully select a dry mounting location where the unit will not come into contact with water/liquids, which may cause internal damage.
- Not SAE J1171 or UL-1500 certified; Installed unit must be isolated from gasoline fuel source in compliance with 33 CFR §183.410 - Ignition protection, and boat manufacturer instructions.
![]()
![]()
- Check all connections and systems before final installation.
- Do not use unauthorized parts as this may cause malfunctions.
- Do not install this unit where:
- it may interfere with operation of the boat.
- it may cause injury to a passenger as a result of a sudden stop.
- Install this unit away from hot places such as near the heater outlet.
- Optimum performance is obtained when the unit is installed at an angle of less than 60°.
![]()
- When installing, to ensure proper heat dispersal when using this unit, make sure you leave ample space behind the rear panel and wrap any loose cables so they are not blocking the vents.
![Pioneer - MVH-MS310BT - Leave ample space Leave ample space]()
DIN mount installation
- Insert the supplied mounting sleeve into the dash panel.
- Secure the mounting sleeve by using a screwdriver to bend the metal tabs (90°) into place.
- Dash panel
- Mounting sleeve
- Make sure that the unit is installed securely in place.
When not using the supplied mounting sleeve
- Line up the holes on the mounting bracket with the holes on the sides of the unit to attach the bracket.
![]()
- Screw in one screw on each side to hold the unit in place.
- Tapping screw (5 mm × 9 mm, not supplied with product)
- Mounting bracket
- Dash panel or console
Removing the unit (installed with the supplied mounting sleeve)
- Remove the trim ring.
- Trim ring
- Notched tab
- Releasing the front panel allows easier access to the trim ring.
- When reattaching the trim ring, point the side with the notched tab down.
- Insert the supplied extraction keys into both sides of the unit until they click into place.
- Pull the unit out of the dash panel.
![Pioneer - MVH-MS310BT - Removing the unit - Step 2 Removing the unit - Step 2]()
To secure the front panel
The front panel can be secured with the supplied screw.
![]()
- Screw
Installing the microphone
The microphone should be placed directly in front of the boat operator at a suitable distance to pick up their voice clearly.
![]()
Carefully select the mounting location to avoid internal damage by water entering the microphone. Areas subject to water splashes should be avoided.
![]()
It is extremely dangerous to allow the microphone lead to become wound around the steering column or shift lever. Be sure to install the microphone in such a way that it will not obstruct operation. It is recommended to use cable clamps (sold separately) to arrange the lead.
- Slide the microphone base to detach it from the microphone clip.
- Microphone
- Microphone clip
- Microphone base
- Install the microphone as follows.
- Double-sided tape
- Clamp (sold separately)
Basic operation
MVH-MS310BT
![Pioneer - MVH-MS310BT - Controls Controls]()
About the main menu
You can adjust various settings in the main menu.
- Press the M.C. dial to display the main menu.
- Turn the M.C. dial to select one of the categories below, then press to confirm.
- FUNCTION settings
- AUDIO settings
- SYSTEM settings
- ILLUMINATION settings
- MIXTRAX settings
- Turn the M.C. dial to select the options, then press to confirm.
Frequently used operations
Purpose | Operation |
Turn on the power | Press SRC/OFF to turn on the power. Press and hold SRC/OFF to turn off the power. |
Adjust the volume | Turn the M.C. dial. |
Select a source | Press SRC/OFF repeatedly. |
Change the display information | Press DISP repeatedly. |
Return to the previous display/list | Press BAND/ . |
Return to the normal display from the menu | Press and hold BAND/ . |
Change the display brightness | Press and hold BAND/ . |
Boost the bass level | Press BASS. - You can select the bass level ([HI] or [LOW]) in [D.BASS].
|
Setup operation
When you turn the ignition switch to ON after installation, the setup menu appears in the display.
- Turn the M.C. dial to select [LANGUAGE], then press to confirm.
[ENG]
[ESP]
[FRA] - Turn the M.C. dial to select [CLOCK SET], then press to confirm.
- Turn the M.C. dial to adjust the hour, then press to confirm.
The indicator moves to the minute setting automatically. - Turn the M.C. dial to adjust the minute, then press to confirm.
- [QUIT:YES] appears.
To return to the first item of the setup menu, turn the M.C. dial to select [QUIT:NO], then press to confirm. - Press the M.C. dial to confirm the settings.
Canceling the demonstration display (DEMO OFF)
- Press the M.C. dial to display the main menu.
- Turn the M.C. dial to select [SYSTEM], then press to confirm.
- Turn the M.C. dial to select [DEMO OFF], then press to confirm.
- Turn the M.C. dial to select [YES], then press to confirm.
Tuner operation
Receiving preset stations
- Press SRC/OFF to select [RADIO].
- Press BAND/
to select the band.
[FM1]
[FM2]
[FM3]
[AM] - Press a number button (1/
to 6/
).
Best stations memory (BSM)
- After selecting the band, press the M.C. dial to display the main menu.
- Turn the M.C. dial to select [FUNCTION], then press to confirm.
- Turn the M.C. dial to select [BSM], then press to confirm.
To store stations manually
- While tuned to the station you want to store, press and hold one of the number buttons (1/
to 6/
) until it stops flashing.
USB/iPhone®/AUX operation
(iPhone source is not available when [USB MTP] is set to [ON] in the SYSTEM settings.)
USB/iPhone
- Open the USB port cover.
- Plug in the USB device/iPhone using an appropriate cable.
MTP connection
A device installed with Android OS 4.0 or most later versions can be connected to the unit via MTP using the cable supplied with the device. However, depending on the connected device, OS version or the number of files in the device, audio files/songs may not be able to be played back via MTP.
NOTE
If you use an MTP connection, [USB MTP] needs to be set to [ON] in the SYSTEM settings.
AUX
- Insert the stereo mini plug into the AUX input jack.
- Press SRC/OFF to select [AUX IN] as the source.
Bluetooth connection
Up to two Bluetooth mobile devices can be connected simultaneously.
- Turn on the Bluetooth function of the device.
- Select the unit name shown in the device display.
- Make sure the same 6-digit number appears on this unit and the device.
- Select [YES].
Bluetooth telephone
Basic operations
Purpose | Operation |
Answer an incoming call | Press any button when a call is received. |
End a call | Press . |
Reject an incoming call | Press and hold when a call is received. |
Activating voice recognition mode
- Press and hold
and then talk into the microphone to input voice commands.
To exit voice recognition mode, press BAND/
.
Making a connection with Pioneer Smart Sync
Pioneer Smart Sync is the application that intelligently brings your maps, messages, and music together.
![]()
![www.apple.com]()
![play.google.com]()
![]()
Do not attempt to operate the application while driving. Make sure to stop your boat in a safe location before attempting to use the controls on the application.
- Enter the SYSTEM menu (refer to "About the main menu").
- Turn the M.C. dial to select [APP CONTROL], then press to confirm.
- Turn the M.C. dial to select one of the below.
- Select [WIRED] for the USB connection.
- Select [BLUETOOTH] for the Bluetooth connection.
- Turn the M.C. dial to select [AUTO APP CONN], then press to confirm.
- Turn the M.C. dial to select [ON], then press to confirm. 6 Connect this unit with the mobile device via USB or Bluetooth. Pioneer Smart Sync on the iPhone/Android device starts automatically.
NOTE
Regardless of whether the [AUTO APP CONN] setting is set to [ON] or [OFF], you can also perform the following to start Pioneer Smart Sync.
- For devices other than a USB-connected Android device, press SRC/OFF to select any source and press and hold the M.C. dial.
- For iPhone, launch Pioneer Smart Sync on the mobile device.
Listening to Pandora®
(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)
Update the Pandora application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.
- Enter the SYSTEM menu (refer to "About the main menu").
- Turn the M.C. dial to select [APP CONTROL], then press to confirm.
- Turn the M.C. dial to select one of the below.
- Select [WIRED] for the USB connection.
- Select [BLUETOOTH] for the Bluetooth connection.
- Press SRC/OFF to select [PANDORA].
- Launch the Pandora application on the mobile device and start playback.
Listening to Spotify®
(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)
Update the Spotify application to the latest version before use.
Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.
- Enter the SYSTEM menu (refer to "About the main menu").
- Turn the M.C. dial to select [APP CONTROL], then press to confirm.
- Turn the M.C. dial to select one of the below.
- Select [WIRED] for the USB connection.
- Select [BLUETOOTH] for the Bluetooth connection.
- Press SRC/OFF to select [SPOTIFY].
- Launch the Spotify application on the mobile device and start playback.
![]()
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Pioneer MVH-MS310BT - Marine Digital Media Receiver Quick Start Guide
Need Assistance?
Do you have a question about the MVH-MS310BT that isn't answered in the manual? Leave your question here.