Summary of Contents for GP3D RC10GX'89 IFMAR WORLDS REPLICA CONVERSION KIT
- Page 1 ASSEMBLY MANUAL ASSEMBLY MANUAL RC10GX ’89 IFMAR WORLDS REPLICA CONVERSION KIT Version 1.1 ©GP3D 2022...
- Page 2 Firstly; A MASSIVE THANK YOU FOR YOUR SUPPORT AND PASSION! We would like to thank you for purchasing our GP3D RC10GX ’89 IFMAR Worlds Replica Conversion Kit. As you have purchased this kit it means you are passionate about the history of our beloved R/C hobby and in particular one of the most iconic and revolutionary R/C cars we have seen ...
-
Page 3: Table Of Contents
STEP 9.5 – GEARBOX TOP PLATE INSTALLATION ..........................20 STEP 9.6 – GEARBOX CASING STAND-OFFS ............................20 STEP 10.1 – WHEEL ADAPTERS ................................21 STEP 10.2 – MOTOR PLATE – CUT OUT GUIDE ............................21 RC10GX CONVERSION KIT – COMPLETED! ............................. 22 Version 1.1 ©GP3D 2022... -
Page 4: Icons & Symbols
Clean up part/edges with scalpel and/or sand paper Gentle Exercise care and love and gently tighten! Information Indicates some extra information or hints or options Very Important! Highlights a very important item to take note Check Check your assembly matches the picture Version 1.1 ©GP3D 2022... -
Page 5: Step 1.1 - Rear Bulkhead
Refer STEP 10.2 STEP 1.2 - REAR SHOCK TOWER 4-40cs x7/16” Sand approx ~0.4mm off bottom 4-40cs x5/16” edge of tower to clear the rear edge of top deck. Version 1.1 ©GP3D 2022... -
Page 6: Step 1.3 - Chassis
ASSEMBLY MANUAL STEP 1.3 - CHASSIS Cutting these threads will be tight, use steel bolt only, take your time. Light grease on thread can help. 8-32cs x1/2” Phillips STEP 1 - COMPLETED Version 1.1 ©GP3D 2022... -
Page 7: Step 2.1 - Battery Cups
ASSEMBLY MANUAL STEP 2.1 – BATTERY CUPS 4-40cs x7/16” STEP 2.2 – SIDE BODY SUPPORTS Tip: use thin double-sided tape under body support to resist rotation 4-40cs x7/16” Version 1.1 ©GP3D 2022... -
Page 8: Step 3.1 - Rear Top-Deck Supports
STEP 3.1 – REAR TOP-DECK SUPPORTS Note: the angle here indicates the right-hand side component Note: this component is 3D printed and has minimal material around the threads therefore be gentle. L&R 4-40cs x5/16” STEP 3 - COMPLETED Version 1.1 ©GP3D 2022... -
Page 9: Step 4.1 - Front Bulkhead - Shock Tower
STEP 4.1 – FRONT BULKHEAD – SHOCK TOWER Remove any Brim material Drill out holes slightly if needed, so that bolt doesn’t damage the fibreglass 4-40 socket x3/8” STEP 4.2 – ATTACH FRONT BULKHEAD 4-40cs x5/16” 4-40cs x3/8” Version 1.1 ©GP3D 2022... -
Page 10: Step 4.3 - Front Bulkhead Tips
4-40cs bolts and add lock nuts to avoid loosening. Optionally drill with 1/8” bit and/or use a reamer until your hinge pins slide in with small force, they do not have to rotate freely. STEP 4 - COMPLETED Version 1.1 ©GP3D 2022... -
Page 11: Step 5.1 - Top Deck & Front Body Post
Note: Hole for body pin is oriented crossways 4-40 button x1/4” STEP 5.2 – INSTALL TOP DECK 4-40 button x1/4” 4-40 button x3/8” L&R 4-40 button x3/8” Ensure rear edge of Top Deck slides under bottom edge of Rear Shock Tower Version 1.1 ©GP3D 2022... -
Page 12: Step 5.3 - No Coast Stand-Offs
ASSEMBLY MANUAL STEP 5.3 – NO COAST STAND-OFFS Available Separately: NoCoast RC alloy stand-offs Part# NCRC-191302 STEP 5 - COMPLETED Version 1.1 ©GP3D 2022... -
Page 13: Step 6.1 - Battery Strap
Leave 4-40 slightly loose to ensure battery strap can still move STEP 6.2 – OPTIONAL LONG BATTERY POSITION Use the longer Battery Strap component included Full length LiPo (or position Shorty forward) Mount Battery Cup in forward position Version 1.1 ©GP3D 2022... -
Page 14: Step 6.3 - Esc Support
ESC Support Positioning of double-sided tape pieces… STEP 6 - COMPLETED Ensure enough double-sided tape thickness so that the ESC Support just clears the rear battery strap 4-40 socket bolt heads. Version 1.1 ©GP3D 2022... -
Page 15: Step 7.1 - Rear Suspension Arms
STEP 7.2 – REAR SUSPENSION ASSEMBLY COMPLETED Ensure smooth/free movement of arms LEFT Sand edges of arms to clean up any print roughness as desired RIGHT Use your E-clips to secure hinge pins Version 1.1 ©GP3D 2022... -
Page 16: Step 7.3 - Install Rear Suspension Arms
ASSEMBLY MANUAL STEP 7.3 – INSTALL REAR SUSPENSION ARMS Sand/Dremel the arm and/or carbon edges, if required, to ensure arms do not bind (front and rear areas) 8-32cs x1/2” STEP 7 - COMPLETED Ensure arms pivot freely Version 1.1 ©GP3D 2022... -
Page 17: Step 8.1 - Front Suspension Arms
STEP 8 - COMPLETED Ensure arms pivot freely Sand edges of arms to clean up any print roughness as desired Use your E-clips to secure hinge pins Version 1.1 ©GP3D 2022... -
Page 18: Step 9.1 - Gearbox
4-40 x3/8” threads in Tip: If needed, add 1/8” shims under bolt heads if needed to avoid bolt tip protruding past motor plate into slipper. 4-40 socket x3/8” Version 1.1 ©GP3D 2022... -
Page 19: Step 9.3 - Gearbox Installation
ASSEMBLY MANUAL STEP 9.3 – GEARBOX INSTALLATION Rear Suspension omitted in this view for clarity! STEP 9.4 – GEARBOX TOP PLATE Note: Counter sink underside 8-32cs x1/2” Version 1.1 ©GP3D 2022... -
Page 20: Step 9.5 - Gearbox Top Plate Installation
STEP 9.5 – GEARBOX TOP PLATE INSTALLATION 4-40 socket x3/8” STEP 9.6 – GEARBOX CASING STAND-OFFS Rear Suspension omitted in this view for clarity! 3x Motor Plate Stand-offs 4-40cs x3/16 or 1/4” For your motor guard Version 1.1 ©GP3D 2022... -
Page 21: Step 10.1 - Wheel Adapters
There are two small cut outs that are dremelled from the motor plate to replicate the original: To clear the rear extreme inner camber link position; ball cup pivot To clear the back of the rear inner arm pivot/hinge pin/E-clip #1) remove this area #2) remove ‘very minor’ material here Version 1.1 ©GP3D 2022... -
Page 22: Rc10Gx Conversion Kit - Completed
Your RC10GX conversion kit is “complete”… …now “just” your remaining components to go…! …OVER TO YOU TO FINISH YOUR AMAZING BUILD!!! Please send us your progress / finished build photos and we will add to our Customer Gallery! Version 1.1 ©GP3D 2022...
Need help?
Do you have a question about the RC10GX'89 IFMAR WORLDS REPLICA CONVERSION KIT and is the answer not in the manual?
Questions and answers