Related Manuals for Metallkraft MBSM Series
Summary of Contents for Metallkraft MBSM Series
- Page 1 Operating Instruction Metal-belt sander MBSM 75-200-2 MBSM 150-200-2 MBSM 150-200-2 MBSM 75-200-2...
-
Page 2: Table Of Contents
Contents 1 Introduction ..........3 Product identification 1.1 Copyright ............3 1.2 Costumer service..........3 Metallkraft 1.3 Limitation of liability..........3 2 Safety ............4 Metal- belt sander 2.1 Symbol explanation ..........4 2.2 Obligations of the operating company ....4... -
Page 3: Introduction
Introduction 1.3 Limitation of liability All information and notes in these operating instructions With the purchase of the device of METALLKRAFT you were summarized taking the applicable standards and have made a good choice. rules, the state-of-the-art and our long-term knowledge Thoroughly read the operating instructions before and experiences into consideration. -
Page 4: Safety
Safety Safety Tips and recommendations This paragraph will give you an overview of all important Tips and recommendations safety packages for the protection of persons as well as for the safe and undisturbed operation. Other taskba-sed This symbol highlights useful tips and recommenda- safety notes are included in the individual chapters. -
Page 5: Requirements To Staff
Safety Furthermore the operating company is responsible to Manufacturer: keep the machine always in a technically flawless state. Certain works may only be performed by specialist per- Thus, the following applies: sonnel of the manufacturer. Other personnel is not au- thorized to perform these works. -
Page 6: Safety Devices
Safety 2.5 Safety devices 2.6 Safety identifications on the Metal- belt sander To protect against flying sparks, a protective screen is at- tached to the housing above the contact wheel. The on- There are safety markings and instructions attached to off switch unit is combined with an emergency stop the metal- belt sander (Fig. -
Page 7: Additional Safety Regulations
Intended use - Keep the machine and its working environment al- 2.7 Additional safety regulations ways clean. Ensure adequate lighting. - In principle, secure your workpiece when working - The workpiece may only be brought into contact with suitable clamping devices. Make sure there is with it after the grinding belt has been switched on. -
Page 8: Technical Data
Technical Data WARNING! WARNING! Danger in case of misuse! Misuse of the device can lead to dangerous situa- It should be noted that the duration of the sound tions. exposure, the nature and condition of the work area as well as other machines that are in operation at the - Only operate the machine in the power range spec- same time influence the noise level in the workplace. -
Page 9: Packaging
Description of the device Transport Hazardous areas, bumps and imperfections must be in- spected prior to transport. The removal of hazardous Improper transport is prone to accidents and can cause areas, bumps and obstructions at the time of transport by damage or malfunctions to the machine, for which we do other employees leads to considerable dangers. -
Page 10: Optional Accessory
Settings 1 Machine foot - The device may only be installed and operated in dry, ventilated rooms. 2 Interlock angle adjustment - Avoid places near chips or dust generating ma- 3 Electric engine 400 V ~ 50 Hz chines. 4 Switching box / ON-OFF-Switch - The place of installation must be vibration-free, i.e. -
Page 11: Operation Of The Machine
Operation of the machine - Before starting the machine, make sure that the sanding belt is free to rotate and that it is not ATTENTION! braked or blocked by any workpieces. The grain size of the abrasives must be selected - Lubricate regularly according to item maintenance. -
Page 12: Cleaning, Maintenance And Service
With the machine off, remove the chips and dust from METALLKRAFT dealer. Please write down the follow- the cooling openings of the motor with a hand brush or ing information from the machine or the operating in- brush. -
Page 13: Disposal, Recycling Of Used Devices
Disposal, recycling of used devices 12 Disposal, recycling of used Distur- Possible Measures devices bances causes Engine Damaged on / Have the machine Please take care in your own interest and in the interest of does not off switch. checked by an elec- the environment that all component parts of the machine start. -
Page 14: Disposal Of Lubricants
Spare parts 12.3 Disposal of lubricants NOTE! The manufacturer warranty shall be rendered void in ATTENTION! the event of a use of unauthorized spare parts. Please pay attention to an environmentally friendly Spare parts are available from authorised retailers or di- disposal of the used coolants and lubricants. -
Page 15: Spare Parts Drawings
Spare parts 13.2 Spare parts drawings In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorized dealer. Fig. 7: Spare parts drawing 1 - MBSM 75-200-2 and MBSM 150-200-2 MBSM 75-200-2 | MBSM 150-200-2 | Version 2.05... -
Page 16: Parts List
Spare parts 13.3 Parts list MBSM 75-200-2 MBSM 150-200-2 Pos. Description Quan- Size Item number Item number tity COUNTERSUNK SCREW ISO 7047 M4X6 0392207501 0392215001 COVER BELT ADJUSTMENT 0392207502 0392215002 WORKPIECE SUPPORT 0392207503 0392215003 HOLDER WORKPIECE SUPPORT 0392207504 0392215004 WASHER 0392207505 0392215006 Φ8... - Page 17 Spare parts MBSM 75-200-2 MBSM 150-200-2 Pos. Description Quan- Size Item number Item number tity FIXING ELEMENT 0392207533 0392215033 COUNTERSUNK SCREW M6X50 0392207534 0392215034 WASHER 0392207535 0392215035 Φ6 THREADED BOLTS M8X12 0392207536 0392215036 COVER PLATE 0392207537 0392215037 LOCKING NUT 0392207538 0392215038 0392207539 0392215039...
- Page 18 Spare parts MBSM 75-200-2 MBSM 150-200-2 Pos. Description Quan- Size Item number Item number tity COUNTERSUNK SCREW ISO 7047 M4X6 0392207567 0392215067 CUP SPRING 0392207568 0392215068 HEXAGON SCREW 6X12 0392207569 0392215069 REMOVABLE SHEET 0392207570 0392215070 ADJUSTABLE HANDLE 0392207571 0392215071 MONTING PLATE 0392207572 0392215072 SCREW...
-
Page 19: Circuit Diagram
Circuit diagram 14 Circuit diagram Fig.5: Circuit diagram MBSM 75-200-2 and MBSM 150-200-2 MBSM 75-200-2 | MBSM 150-200-2 | Version 2.05... -
Page 20: Ec-Declaration Of Conformity
According to Machinery Directive 2006/42/EC Annex II 1.A Manufacturer / distributor: Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Straße 26 D-96103 Hallstadt hereby declares that the following product Product Group: Metallkraft® Metallbearbeitungsmaschinen Machine type: Metal- belt sander Description of the machine*: MBSM 75-200-2 MBSM 150-200-2 Item number*:... -
Page 21: Notes
Notes 16 Notes MBSM 75-200-2 | MBSM 150-200-2 | Version 2.05... - Page 22 www.metallkraft.de...
Need help?
Do you have a question about the MBSM Series and is the answer not in the manual?
Questions and answers