Summary of Contents for Hilltip Ice STRIKER 600 TR
- Page 1 19 November, 2021 Version 1.2 STRIKER Owner’s manual 600-1000 liter poly electric tractor spreader this manual replaces all editions with an earlier date.
-
Page 2: Table Of Contents
IceStriker General InformatIon ..........3 spreader parts . -
Page 3: General Information
GeNeral iNForMatioN IceStriker Spreader parts tarp cover license plate kit and rear light (optional) Beacon light (optional) auger emergency stop button (inside hopper) spinner... -
Page 4: Technical Information
IceStriker technical information Spreader SpecIfIcatIonS 600 tr 800 tr 1000 tr overall width 1500 mm 1500 mm 1500 mm Height 1500 mm 1650 mm 1800 mm capacity (water level) 550 l 750 l 950 l capacity (rounded) 630 l 850 l 1050 l Weight (empty) 320 kg... -
Page 5: Safety Information
saFety iNForMatioN IceStriker Safety definitions WARNING CAUTION implies a potentially hazardous implies a potentially hazardous situation that, if not avoided, could situation that, if not avoided, may result in death or serious personal result in minor or moderate injury. injury. it may also be used to alert against unsafe practices. -
Page 6: Recommended Vehicle Requirements
IceStriker WARNING WARNING always keep bystanders a minimum Wait for auger and spinner to stop and of 10 meters away when operating the lock out power before servicing the spreader. spreader. CAUTION NOTE Use a good quality multi-purpose empty and clean the hopper after each grease to lubricate grease fittings after use. -
Page 7: Warning And Caution Labels
IceStriker Warning and caution labels please become familiar with warning and caution labels on the spreader. Warning - Handling of abrasive and chemical material can cause injury - Visible when removing the spinner assembly Warning - rotating auger! Keep hands clear. Wrench might slip when working with auger - located on the chute Warning - Keep away from spinner... -
Page 8: Installation And Operation
iNstallatioN aNd operatioN IceStriker control placement the controller should be mounted in a place where it can easily be reached and doesn’t interfere with the access to vehicle controls or other equipment. Make sure that the spreader control panel doesn’t block any vehicle airbag areas. -
Page 9: Accessory Cables
IceStriker accessory cables emergency stop (standard) Black = Water pump yellow = Beacon light Blue camera power feed White = led worklight mounting the top screen Place the screen so that it fits the hopper opening. Fasten the brackets on both sides of the screen, the flat bracket should be in the middle. -
Page 10: Mounting The Tarp Cover Assembly
IceStriker mounting the tarp cover assembly insert one of the longer pipes into the insert brackets in both sides. opening in the cover (pre-mounted) connect pipe and brackets with bolts in place the second long pipe under the both ends. cover and connect to the brackets using bolts... - Page 11 IceStriker insert the short pipe into the cover, insert rubber wires into the two parallel to the other pipes. remaining openings in the cover. place washer and bush around the connect washer, bracket, bush and bracket, as shown in the picture. rubber wire with bolt.
-
Page 12: Spreading Pattern
IceStriker Spreading pattern rotate the spinner plate to position the material drop point and change spreading pattern. = material drop point spinner plate rotated ccw drop point in center spinner plate rotated cw rotate jammed auger manually if the error code “auger jammed” appears, the auger can be rotated manually to release any solidified material or rocks. Always turn off the spreader before servicing it. -
Page 13: Loading
loadiNG IceStriker average material weights material Weight WARNING (kg/m do not overload your vehicle beyond Fine salt - dry 1201 GVWr or GaWr, overloading could result in accident or damage. coarse salt - dry coarse sand - dry 1602 CAUTION coarse sand - wet 1922 these material weights are only... -
Page 14: Maintenance
MaiNteNaNce IceStriker maintaining the spreader WARNING CAUTION power should always be shut • do not operate a damaged off before and during service or spreader or a spreader in need of maintenance of the sperader. maintenance • spreader should be emptied and cleaned after each use. left over WARNING material could freeze or solidify in Never remove spreader with material... -
Page 15: Storage
IceStriker Important: It is strongly recommended and of great importance that you regularly apply dielectric grease on all electrical connections and protect them with caps when not in use to prevent corrosion. always keep caps on when to prevent corrosion, use While cables are connected, the cables are not connected dielectric grease on electrical... -
Page 16: Optional Liquid Systems
optioNal liqUid systeMs IceStriker caution! the liquid tank should always be emptied after each use (turn the red handle). Also empty the filter. If liquids are left in the tank for an extended period of time, it may freeze and cause damage to your spreader. Also make sure to clean the filter regularly. pre-wet (optional) 1. start with selecting pre-Wet as spreading mode in the controller. Go to: Main menu >... -
Page 17: Spray-Bar (Optional)
IceStriker Spray-bar (optional) 1. start with selecting spray-bar as spreading mode in the controller. Go to: Main menu > settings > Wetting > select spray-bar 2. You will find a handle on the right side of the chute. point the handle towards spray Bar 3. attach spray-bar to the chute: 4. -
Page 18: Bladder Tank (Optional)
IceStriker Bladder tank (optional) 1. You will find a handle on the left side of the chute. point the handle towards Bladder taNK 2. remove the plug from the bottom of the spreader 3. place the bottom support plate and bladder tank. pull the hose trough the hole of the plate and the hopper. -
Page 19: Hose Reel (Optional)
IceStriker hose reel (optional) 1. start with selecting Hand spray as spreading mode in the controller. Go to: Main menu > settings > Wetting > select Hand spray 2. You will find a handle on the right side of the chute. point the handle towards HaNd spray Important! liquid system clean-out instructions 1. -
Page 21: Warranty Information
What will we do to correct problems? Hilltip or an authorized dealer will repair or replace the product or part at no charge using either new or refurbished replacement parts. how long does the coverage last? the Warranty period for products purchased from Hilltip, or an authorized dealer is two (2) years from the date of purchase. -
Page 22: Certificate Of Conformity
Road Traffic Regulations in European countries: - 2006/42/EC - EN 15597-1 I, the undersigned, hereby declare that the equipments specified above, that have been assambled by Oy Hilltip Ab, conforms to the above directives and standards Pietarsaari 10th August, 2020 Signature: Printed Name: Tom Mäenpää... - Page 24 +358 50 5983 026 phone: +358 50 3659 415 pukkisaarentie 6 FiN-68600 pietarsaari www.hilltip.com info@hilltip.com Finland Construction, specifications and other details are subject to change without notice.
Need help?
Do you have a question about the Ice STRIKER 600 TR and is the answer not in the manual?
Questions and answers