Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Redexim Rink DS3800
Summary of Contents for Redexim Rink DS3800
- Page 1 Operating and Part Redexim manual RINK Model DS3800 Serial number: NOTE: IN ORDER TO ENSURE THE SAFE USE AND TO ACHIEVE THE BEST PERFORMANCE, IT IS ESSENTIAL THAT THIS OPERATING MANUAL IS CAREFULLY READ BEFORE THE RINK IS USED. 0719 English...
-
Page 2: Table Of Contents
T A B L E O F C O N T E N T S Contents Page Safety regulations................ Short description ................. Technical data................First use..................Operation ....................* Before every ride................. * Coupling and taking off .............. * Loading..................* Spreading .................. -
Page 3: Safety Regulations
SAFETY REGULATIONS Topdresser DS3800 is built solely for spreading small-grained, loose material such as sand, small granular material or similar products. Any other usage is not in accordance with the indicated use. The manufacturer does not answer for any damage resulting from incorrect usage. The user alone has to incur the risk. - Page 4 SAFETY REGULATIONS (6) Before starting work, the operator must make himself familiar with all fittings and controls as well as their functioning. Spreaders must be properly attached (Risk of injuries !) Before driving away, check the immediate vicinity and care for a good field of vision. (7) Whilst spreading is in operation, no one is allowed to enter the loading ramp.
-
Page 5: Short Description
SHORT DESCRIPTION The Topdresser DS800/DS1200 is used for spreading small-grained, loose material, such as sand, small granular material or similar products. The spreading equipment of the Topdresser is driven by a gear box with hydraulic motor for conveyor belt and a separate hydraulic motor for each spinner. -
Page 6: First Use
FIRST USE * Should the spreader be used on public roads (German law: only possible with licensing certificate and registration) Attach license plate to plate holder at the left-handed rear side. - Check lighting set * After the first ride with a full load - Retighten wheel nuts. -
Page 7: Coupling And Taking Off
OPERATION Coupling and taking off - Attach spreader to towing vehicle. Mount spreader on back of utility vehicle. - Carry out hydraulic connection (see page 8 for further details): - Oil circulation is required. Install valve (5) for conveyor belt on towing vehicle. Please use therefore enclosed bracket. -
Page 8: Spreading
SPREADING If you run the machine, the spinner discs will be activated immediately. The conveyor belt and the closing gate will be activated with the valve. First the gate opens and part of a second later the conveyor belt starts moving. Before starting work, please choose gate opening 1-4 at the rear of the machine. Controls: Regulator for setting the speed of the spinner discs Regulator for setting the speed of the conveyor belt... -
Page 9: Repair And Maintenance
REPAIR AND MAINTENANCE Lubricate spreader (every 50 operating hours) Lubricate with multi-purpose grease: 1 Bearings on both sides of the spreading discs 2 Bearings on both sides of the rear conveyor shaft 3 Bearings on both sides of the front conveyor shaft Bearings without a lubricating nipple require no greasing. -
Page 10: Oil Change For Conveyor Belt Gears (Every 2 Years)
REPAIR AND MAINTENANCE Oil change for conveyor belt gears (every 2 years.) - Unscrew filler screw (1). - Loosen drain plug (2) from the below inside area and drain off oil. - Screw on drain plug with new gasket. - Add 0.6 l Oil SAE 120 to 140. - Screw on filler screw with the new gasket. -
Page 11: Adjust Sand Droping Plate (As Required)
REPAIR AND MAINTENANCE Adjust sand droping plate (according to requirements) The sand droping plate has to be adjusted, if the spreading pattern is uneven. Therefore you have to increase or reduce the angle of the plate. In addition, each spreading showel can be adjusted as well. - Loose screw (1) - Droping plate (2) in requested position. -
Page 12: Rink Disk Spreader Ds3800 Spread Table
Rink Disc Spreader DS 3800 Spreading Guide Application Spinner Floor Control Gate Door Approx. Topdressing Regulator Spreading Width 8-10 Light Medium Heavy... -
Page 13: Establish The Disk By Uneven Spriding Pattern
Disk settings in case of unequal spreading pattern: A: Only outside material concentration – move all vanes in direction B B: Only inside material concentration – move all vanes in direction A For dry sand material you must bring the funnel in position 1... -
Page 14: Installing And Removing The Conveyor Belt
REPAIR AND MAINTENANCE Installing and removing the conveyor belt - Loosen screws on both sides (1) and remove the chassis. - Remove the spreading device by loosening the screws (2). - Release the tension on the conveyor belt on both sides (3). - Remove the bearing on the right seen in the direction of travel (4). -
Page 15: Problem Analyse
problem analyse gate will not open no sand in hopper fill up the hopper disc will not spread wide enough spinners turn to slow check oil supplier sand layer to thin not enough sand comes on to the open gate more, increase the belt disc. -
Page 16: Order Replacing Parts
Parts list RINK DS3800 Ordering spare parts To ensure that your spare parts order can be processed quickly, always specify the following data when ordering. - Chassis number / Ident. number - Model (year of construction if available) - Part number from respective spare parts list...
Need help?
Do you have a question about the Rink DS3800 and is the answer not in the manual?
Questions and answers