Advertisement
Quick Links
CudaCam
Bullet Camera Installation in an Outdoor Enclosure
https://campus.barracuda.com/doc/46897355/
This document explains how to install a Bullet Camera into an outdoor enclosure.
Step 1: Install the Wi-Fi Antenna (Optional)
If you will be installing a Wi-Fi antenna, complete the steps in this section.
Otherwise, proceed to the next section, Ethernet Cable Installation.
1.
Open the enclosure.
2.
Drill a ¼" hole toward the back of the enclosure. Remove all burrs and cuttings.
3.
Install the RP-SMA extension cable into the hole in the back, using the supplied lock washer and
nut.
Bullet Camera Installation in an Outdoor Enclosure
1 / 11
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for baracuda CudaCam
- Page 1 CudaCam Bullet Camera Installation in an Outdoor Enclosure https://campus.barracuda.com/doc/46897355/ This document explains how to install a Bullet Camera into an outdoor enclosure. Step 1: Install the Wi-Fi Antenna (Optional) If you will be installing a Wi-Fi antenna, complete the steps in this section.
- Page 2 CudaCam This figure shows a completed antenna. Note: Point antenna straight down (vertically), for best results. Do not position antenna horizontally, as shown. Bullet Camera Installation in an Outdoor Enclosure 2 / 11...
- Page 3 CudaCam Step 2: Install Ethernet Cable Ethernet cable provides power to the camera, regardless of whether Wi-Fi is used to transmit data. Use the following recommendations: Power over Ethernet (PoE) – either an 802.3af PoE supply or a 48VDC power supply Current –...
- Page 4 CudaCam Route the cable into the enclosure through the cable gland. Terminate the cable with an RJ-45 connector so it can be connected to the camera, as shown below. Continue with the following section, Camera Installation. Bullet Camera Installation in an Outdoor Enclosure...
-
Page 5: Step 3: Install The Camera
CudaCam Step 3: Install the Camera To install the camera: Remove the locking screws that keep the camera holder in place. Remove the camera holder. In the original camera packaging, locate one of the white metallic spacers. Bullet Camera Installation in an Outdoor Enclosure... - Page 6 CudaCam Mount the camera to the holder as shown, using the ¼"-20 screw that came in the parts bag and the white metallic spacer from the original camera packaging. Snap the camera and holder back into the enclosure. Position the camera so the lens is about ¼"...
- Page 7 CudaCam Connect the Ethernet cable to the camera. If you are using Wi-Fi, connect the RP-SMA extension cable to the camera. Mount the enclosure in a suitable location. Step 4: Assemble the Mount To assemble the mount: Disassemble the highlighted section of the arm mount.
- Page 8 CudaCam Remove the base from the bottom of the case. Attach both bases together using the supplied screws, then install it back to the arm mount. Bullet Camera Installation in an Outdoor Enclosure 8 / 11...
- Page 9 CudaCam Install the full arm on the camera case, and adjust the angles as needed. This figure shows a completed arm mount installation. Bullet Camera Installation in an Outdoor Enclosure 9 / 11...
- Page 10 CudaCam The unit is now ready to be installed in the location you have chosen. Bullet Camera Installation in an Outdoor Enclosure 10 / 11...
- Page 11 CudaCam Figures WiFi2.png WiFi3.png WiFi4.png EthernetCombo.png Ethernet5.png Ethernet6.png Ethernet7.png CamInstall1.png CamInstall2.png CamInstall3a.png CamInstall4.png CamInstall5.png mountAssy1.png mountAssy2.png mountAssy3a.png mountAssy4a.png mountAssyFinal.png © Barracuda Networks Inc., 2023 The information contained within this document is confidential and proprietary to Barracuda Networks Inc. No portion of this document may be copied, distributed, publicized or used for other than internal documentary purposes without the written consent of an official representative of Barracuda Networks Inc.
Need help?
Do you have a question about the CudaCam and is the answer not in the manual?
Questions and answers