Advertisement
Quick Links
Advertisement
Summary of Contents for Sense t Series
- Page 1 Series Manual Part 1...
- Page 3 Series Manual Part 1...
- Page 4 Arriving to the jobsite I see Lets start with the route. I see no interference obstacles test and range predictions Range Transmitter prediction menu...
- Page 5 Transmitter programming Chose Get back Transmitter to the Main type for menu. accurate range Go to Range prediction prediction Range Range prediction st prediction Keep measured data of range predictions Change Transmitter power to get optimal combination of “Frequency/Power” at the measuring point Range prediction st Short button press...
- Page 6 We strongly recommend make interference test along the whole route of future drilling Make interference Measure test along drilling path to define one or several Measure best modes (frequency/power mode) Saved measurements Erase last line Back Clear the table ...
- Page 7 You can programm up to 7 modes in the Transmitter: freq/power/sleep There are some interferences, but it can mode/protocol be solved! Programming the Transmitter Transmitter programming st Lets programm it! Chose Transmitter type Transmitter type st Transmitter programming st Transmitter type st Use the buttons to move around the table and change values...
- Page 8 Place the power supply into the Transmitter The Receiver is waiting with correct polarity. 2 for the Transmitter to elements of size C or 1 - turn on size 2C Wait 5 seconds (Transmitter in Close the battery cap horizontal position) and lay the Transmitter horizontally next to the to let it turn on...
- Page 9 Go to the Transmitter menu, then to Navigation Exit Navigation Current operating mode of the Receiver and the Transmitter Making sure the Receiver is receiving a signal from the Transmitter Transmitter programmed ...
- Page 10 To obtain information about the Transmitter and the drilling head, it is necessary to make the Transmitter Quiz Transmitter menu Turn on the Transmitter and place it in the drill head Transmitter menu Transmitter programming Transmitter programming Transmitter programming...
-
Page 11: Power Consumption
Type Transmitter Number Transmitter Transmitter Total Programmed Transmitter time and max. Transmitters temperature Modes Battery voltage Power consumption Temperature POWER CONSUMPTION Power consumption allows, among other things, to determine the throughput of the drilling head Power consumption limits for Transmitters: st, st/E, st/C Battery type Alkaline 1C, Li-Ion 2C and Li-Ion 1C... - Page 12 Important!!! If the power consumption limit is exceeded, the battery life will decrease proportionally. The range of signal Transmission from the Transmitter will not decrease Transmitter’s programmed modes Transmitter Press and hold Copy OK to transfer the Transmitter’s programmed modes to the Receiver ...
- Page 13 After you have programmed the Transmitter and Calibration placed it in the drill must be carried head, proceed to the out at a place calibration with a minimum amount of active interference (like: operating Position the Receiver equipment, parallel to the drill head at a distance of sources of 3 meters...
- Page 14 You have 2 options to calibrate Calibration Option 1 - automatic calibration of all modes Press and hold “down” button Transmitter type st Calibration 3 m Transmitter type st...
- Page 15 Option 2 - manual calibration of each mode Select the desired mode Press and hold the “OK” button Transmitter type st Transmitter type st ...
- Page 16 Location Screen Transmitter menu All necessary information is constantly displayed on the screen of the Receiver No. of telemetry quality of channel Transmitter signal Receiver battery power of level Transmitter signal distance to surface Transmitter angle predicted depth Transmitter (in the vicinity of temperature the Front point) current depth...
-
Page 17: Extra Menu
Extra Menu Setting target depth Display inversion Setting the receiver mode Setting target depth Back Target depth setting Operator of the rig also constantly sees all the necessary information on the screen of the Repeater to achieve a depth of 1m at this point - set the angle to -15.3% ... -
Page 18: Repeater Setup
Now set up telemetry Repeater setup Telemetry Modem tunning Channel 3... - Page 19 Modem tunning Modem tunning Modem Off One Relay Modem tunning Modem tunning Two Relays Three Relays Modem tunning Modem tunning No Relays Channel 2 Setting up a Modem tunning Channel 2 channel on the Receiver Modem tunning Channel 1 Modem tunning Channel 3...
- Page 20 Navigation Repeater We return to the Repeater Location and set the Screen same channel The location system is ready to go ...
- Page 21 Tablet Repeater Characteristics • 8 inch screen • protection class - IP 65 • OS - Android • Power supply 5V, 2A • Internal battery 7400 mAh...
- Page 23 Location screen...
- Page 24 Preparation of executive documentation • graphics and tables: • designed drilling profile • designed obstacles • actual surface profile • actual drilling profile • GPS coordinates • comments • date and time of work performed...
- Page 25 The Repeater has all the functionality of a tablet...
- Page 28 22/14 Oktyabr`skaya str. Ulyanovsk, Russia, 432028 +7 (8422) 45-72-00 +7 (985) 222-40-75 info@sense-hdd.com www.sense-hdd.com...