Datasensing ST 400AD Quick Start Manual

821012270 REV. A ENG ED 03/2022
Datasensing S.r.l.
Strada S. Caterina 235 - 41122 Modena - Italy
Tel. +39 059 420411 - Fax +39 059 253973
web: www.datasensing.com | email: info@datasensing.com
ST 400AD
SENSOR TESTER
ANALOGUE + DIGITAL
SUPPLIED MATERIAL
• Sensor Tester
• User's manual
• Power adapter
• USB cable
USER'S MANUAL
Please read the manual carefully before using this product. This product should be applied
by someone with a certain level of electrical knowledge. Please read and make sure that
you understand how to operate the product before using it. Please keep this manual
readilly accesible for future references when needed.
WARNING
Please comply with the warnings indicated below:
Please do not exceed maximum rated voltage during usage in order to prevent
tester malfunction or fi re.
Please do not apply AC power supply to avoid breakage.
Please do not subject the product to high temperature to avoid scalding
The product contains a non removable Li-ion battery. For the delivery of the product,
!
follow National and IATA regulations.
PRECAUTIONS
Comply with the warnings indicated below for they are important:
• Please do not use it in fl ammable or explosive environments.
• Please do not use it in environments with water, oil, chemicals or steams.
• Please do not disassemble, repair or alter this product.
• Please do not exceed the rated voltage and current.
• Please do not exceed the rated environment.
• Please observe electrical polarity when making connections.
• Please connect load correctly.
• Please avoid short-circuiting the load.
• Please do not operate it ,if the housing is broken.
• When disposing of the tester, please treat it as an industrial waste.
• Please do not use it directly connected to a working machine
WARRANTY
Our products have been tested prior to shipping, however if malfunction occurs, please
contact our offi ces near you and present the failure in details so that we can provide the
best solution to you.
Warranty Period
The warranty period is 1 year starting from the shipment date.
Scope of warranty
If malfunction is caused by the product within the warranty period, free service of repairing
shall be off ered. The cases listed below do not fall into the scope of warranty:
• Failure to comply with these operating instructions or breech of contracts with our
company.
• Any malfunction that is caused by buyer's own device or so ware, instead of our
product's defect
• Malfunction that is caused by modifi cation, part replacement, repair or any other
operation not previously authorized in writing by Datasensing S.r.l.
• Malfunction that is caused by unpredictable factors (such as change of science and
technology) a er the product is delivered from our company.
• Malfunction that is caused by natural disasters such as fi re, earthquake and fl ood; or
abnormally shi ing voltage during charging.
SPECIFICATIONS
0 ... 20 mA
Current Mode
Measurement accuracy: ≤ 0,04mA
0 ... 10 V
Voltage mode
Measurement accuracy: ≤ 0,4V
Sensor ouput type
NPN / PNP (automatic detect)
detection
Output voltage 19 ... 24V
Output current for
≤ 160mA
sensors
(1)
Battery capacity 4000 mAh
Operating time ≥ 10h (sensor @50mA)
Charging time ≤ 9h
Operating temperature -10°C ... +45°C
Weight 200g
Dimension 150x67x26 mm
Functions Short circuit protection; Sleeping mode; Positive pulse
Other functions Flashlight
(1)
the product contains a non removable Li-ion battery. For the delivery of the product, follow the National and
IATA regulations.
FUNCTIONS
Mode switching - Press the MODE button shortly to switch the tester in three modes: current
(I), voltage (V), and switch (D). The result will be displayed on the screen.
Power display - When the tester is working normally, the power will be displayed in the upper
right, and the grid number indicates the remaining power. When it fl ashes, it indicates that the
battery is low and needs to be charged. When charging, the number of fl ashes indicates the
progress of charging. When fully charged, the full battery symbol will fl ash.
Sleep mode - If the tester does not operate for more than 10 minutes, it automatically enters
the sleep state, the 24V power supply and the screen will be turned off ; press the MODE button
or the TEACH-IN button, and the tester returns to the operable state.
Mute mode - Press and hold the TEACH-IN button for more than 6s, the buzzer will sound
once, and the tester enters silent mode. Repeating this operation, the buzzer will sound twice
to indicate that the Mute mode has been exited, and the tester will store the state, and will
remain in the last state when it is turned on again.
Teach-In function - Press the TEACH-IN button, the TEACH-IN (red) terminal will output a high
level voltage, and the voltage logic will match the brown terminal voltage. When the button is
released, the TEACH-IN (red) terminal will output a low level voltage, and the LCD will display
the current Teach-In logic state.
Flashlight function - Press and hold the MODE button for more than 2s, the light will light up,
and the same operation can turn off the light.
Short circuit protection - Short circuit protection is entered when the tester output current
is too high. When a short circuit is detected, the LCD will display "SCP". A er the short circuit
condition is removed, the tester needs to be restarted to return to the normal state.
Note:
• Please make sure the power is off before connecting the cable.
• Please make sure the voltage fl uctuations are within maximum rated range.
• When the power is on, please do not apply the device In the fi rst 0.5 s.
• Please do not subject the device to dust, dirt or vapor.
• Please do not subject the device to water, oil or organic solvent such 1s diluents
• Do not use the device while charging.
!
OPERATING INSTRUCTIONS
Follow the procedure below to operate the tester:
CONNECTIONS
brown
black
blue
other colors
Teach In
1. Connect the sensor wires to the corresponding tester terminals and turn on the
tester.
2. Select the corresponding measurement mode (voltage, current, digital).
3. Press the Teach-in button according to the teaching logic of the product.
4. The measurement results are displayed on the screen.
DIMENSIONS
67.67 67.67
26.64 26.64
MODE Button LED light
TEACH-IN Button TEACH-IN Terminal
USB OUT Connector GND Terminal
USB IN Connector INPUT Terminal
©2022 Datasensing S.r.l.
• All rights reserved • Without limiting the rights under copyright, no part of this
documentation may be reproduced, stored in or introduced into a retrieval system,
or transmitted in any form or by any means, or for any purpose, without the express
written permission of Datasensing S.r.l. • Datasensing and the Datasensing logo are
trademarks of Datasensing S.r.l.
mm mm
POWER Terminal
ON/OFF Button