Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Dionex Manuals
  4. Diagnostic Equipment
  5. ICS-6000
  6. Installation instructions manual

Dionex ICS-6000 Installation Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
ICS-6000 Tablet Installation Instructions
This is an excerpt from the Dionex ICS-6000 Installation manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the ICS-6000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dionex ICS-6000

  • Page 1 ICS-6000 Tablet Installation Instructions This is an excerpt from the Dionex ICS-6000 Installation manual...

  • Page 2: Installing The Tablet

    The Tablet Kit (P/N 22181-62020) contains the tablet and its power supply. When the tablet is purchased from Thermo Fisher Scientific, the ICS-6000 App is installed on the tablet at the factory and a predefined user account is created. •...

  • Page 3: Getting Started

    3 • System Setup 3.9.1 Getting Started 1. Unpack the Tablet Kit (P/N 22181-62020). The kit contains the tablet and tablet power supply (P/N HAZMAT-01-00136), as well as setup instructions from the tablet vendor. (You can disregard the vendor instructions.) 2.
  • Page 4 Dionex ICS-6000 Installation Instructions 3.9.2 Installing the Tablet Arm/Holder 1. Attach the mounting arm (P/N 22181-60500) to the left side of the DC: a. Note the two lines molded into the base of the tablet mounting arm, on the inside of the arm (the side of the arm which is installed against the DC).
  • Page 5 3 • System Setup c. Use a 3 mm socket driver to tighten the screws from the front of the mounting arm (see Figure 3-30). You will need to move the arm to access all three screws. Note: Mounting screw behind arm not visible.
  • Page 6 Dionex ICS-6000 Installation Instructions 3.9.3 Routing the Tablet Power and Ethernet Cables This section explains how to perform a partial installation of the tablet power cable and (if required) the Ethernet cable. The connections will be completed later in the network installation procedure.
  • Page 7 3 • System Setup Set the rest of the kit contents aside for use later. NOTE Ethernet Cable Ethernet Cable USB-to-Network Adapter USB-to-Network Adapter Ethernet Cable Figure 3-32. Tablet Cable Options 3. Working from the mounting arm backward, route the tablet power and Ethernet cables from the tablet holder.
  • Page 8 Dionex ICS-6000 Installation Instructions b. Secure the cable with the spiral wraps on the upper and lower sections of the tablet holder arm. USB Network Spiral Wrap Connector Power Cable Power Cable Routing Figure 3-33. Tablet Power Cable Setup Doc. 22181-97001 02/18...
  • Page 9 3 • System Setup 7. Route both the Ethernet and tablet power cables through the tablet arm cable guide (see Figure 3-34) and back toward the tablet holder. Arm (inside view) Cable Guide Channel Cable Guide Channel Figure 3-34. Mounting Arm Cable Guide 8.
  • Page 10 Dionex ICS-6000 Installation Instructions b. Remove the paper backing from the adhesive strip and press the base of the wiring duct firmly onto the side of the DC. Route the cables through the duct cover and attach it to the base (see Figure 3-35).
  • Page 11 3 • System Setup 3. You can now attach the tablet to the tablet holder. Figure 3-37 shows an example installation. If the setup includes an Ethernet cable, the routing for the cable would be the same as the power cable in the photo. Tablet Power Spiral Wrap Release...
  • Page 12 Dionex ICS-6000 Installation Instructions Place the lower-left corner of the tablet into the tablet arm/holder (see Figure 3-38). Pull up the upper-right corner of the tablet and release it to hold the tablet in place. Tablet Corner Holder Tablet Corner Holder Figure 3-38.
  • Page 13 Whenever a communication error is suspected. 1. On the tablet desktop, tap the Windows start bar. If the tablet was not purchased from Thermo Fisher NOTE Scientific, you must install the ICS-6000 App (see Section 3.11.1) before testing communication. Doc. 22181-97001 02/18...
  • Page 14 Dionex ICS-6000 Installation Instructions 2. Tap the search bar and enter “CMD.” A command prompt window is displayed. 3. Type “ping 192.168.0.1.” This command pings the PC. If the test is successful, a response appears on the screen showing the number of packets successfully transferred.
  • Page 15 3 • System Setup Figure 3-39 provides an overview of connections for both the wireless and Ethernet networks. Ethernet Wireless USB-to-LAN USB-to-LAN Adapter Adapter Ethernet Ethernet Wireless Router Router Back Back Router Router Face Face Wireless Wireless On/Off On/Off Button Button Router Router...
  • Page 16 Dionex ICS-6000 Installation Instructions Unpacking the Tablet Connectivity Kit Unpack the Tablet Connectivity Kit (P/N 22181-62017) and verify the kit contents (see Figure 3-40). Reminder: The following items may have been removed from the kit in order to install the tablet arm and tablet (see Section 3.9.3): one of the two network...

  • Page 17: Installing The Router

    Write down this information before proceeding. 3. Connect the outlet prongs of the router power adapter to an electrical outlet near the Dionex ICS-6000 to which the tablet is attached. If the tablet arm is not attached, see Section 3.9.2.
  • Page 18 Dionex ICS-6000 Installation Instructions otherwise. If necessary, push the wireless on/off button to change the mode. Wireless On Light Wireless On/Off Button Figure 3-41. Wireless Router On/Off Button and Status Light 3.10.2 Installing an Ethernet Instrument PC IPC to Router Connection This section contains setup instructions for an IPC connected via Ethernet.
  • Page 19 3 • System Setup 2. Connect an Ethernet cable (P/N 00302-99-00129) to the USB port on the USB-to-Ethernet adapter (see Figure 3-43, item Figure 3-42. Ethernet USB-to-LAN Connection 3. Connect the other end of the Ethernet cable (P/N 00302-99-00129) to any available LAN port on the router.
  • Page 20 Dionex ICS-6000 Installation Instructions 3.10.3 Installing an Ethernet Tablet The hardware installation allows the tablet to send commands through the router to the IPC. The commands are carried out when they are received from the router. 1. An Ethernet cable (P/N 00302-99-00129) was routed to the rear of the DC...
  • Page 21 3 • System Setup 4. Connect the tablet power, if it is not already connected (see Section 3.9.3). Optional USB Adapter Ethernet Cable Router Ethernet Wi-Fi Optional USB Tablet Cable Adapter On/Off Extension Figure 3-44. Ethernet Connections from the Tablet to the Router 3.10.4 Installing a Wireless Tablet The wireless tablet does not require any physical connections to send data to the IPC, although it is necessary to install a wireless router (see...
  • Page 22 Follow the instructions in this section if the tablet that will be used with the Dionex ICS-6000 is not purchased from Thermo Fisher Scientific. 1. Connect the tablet that will be used with the Dionex ICS-6000 to the Internet. 2. Use Windows Search on the taskbar (or press Windows Key + S) to find “Store.”...
  • Page 23 6. Tap Get to download and install the ICS-6000 App. 7. When the ICS-6000 App installation is complete, a Launch button is displayed on the tablet. 8. For ease of use, localize the ICS-6000 App immediately. Language options include Chinese (simplified and traditional), French, German, Italian, Japanese, Korean, Portuguese, Russian, and Spanish.
  • Page 24 Dionex ICS-6000 Installation Instructions 2. Locate the Tools/ICS-6000 Tablet Setup folder (see Figure 3-45). Figure 3-45. ICS-6000 Tablet Setup Utility Location 3. Right-click the folder, and then click Open. 4. Right-click the ICS6000TabletSetup.exe file, and then click Run as Administrator (see Figure 3-46).
  • Page 25 Pairing is the process of linking, or associating, the tablet with the Chromeleon instrument PC (IPC). Pairing enables communication between the tablet and the IPC, which can then transmit commands to the Dionex ICS- 6000 via Chromeleon. There are two pairing procedures: •...
  • Page 26 Section 3.11.2). 3.12.1 Automatically Pairing the Tablet and Instrument PC 1. On the Windows taskbar, click Start > All Programs > Thermo Chromeleon 7 > ICS-6000 Tablet Configuration. The ICS-6000 Tablet Configuration dialog box appears (see Figure 3-48). Figure 3-48. ICS-6000 Tablet Configuration Dialog Box 2.
  • Page 27 Tap the Thermo Fisher Scientific icon in the center of the screen to display the Log In page (see Figure 3-50). Figure 3-50. ICS-6000 App Log In Page 4. Tap Pair with PC. This selects camera mode for the tablet. 5. When the Scanning window is displayed (see Figure 3-51), prepare to scan the QR code with the tablet camera.
  • Page 28 Dionex ICS-6000 Installation Instructions 6. Click Close to exit the ICS-6000 App. 7. Restart the app and verify that the message “Connected to <IPC>” is displayed at the bottom of the log in page. If the message is not displayed, repeat the automatic...
  • Page 29 3 • System Setup e. Close the System window. 3. Add the instrument PC IP address to the tablet “hosts” file: a. On the tablet taskbar, tap Start. b. On the Start menu, tap All Programs > Accessories > Notepad. c.
  • Page 30 Dionex ICS-6000 Installation Instructions On Console1 - [Console Root], in the left navigation pane, click Console Root > Certificates > Personal > Certificates and right- click to select the Chromeleon 7 Web API Self-Signed certificate. In the Chromeleon 7 Web API Self-Signed drop-down list, select All Tasks and then click Export.
  • Page 31 3 • System Setup 5. Select Local Machine, and then click Next. 6. Click Place all certificates in the following store, browse to locate “Trusted Root Certification Authorities,” and click Next. 7. Click Finish. 8. In the Certificate dialog box, click Install Certificate. g.