Wall Mounting; Assembly And Adjustments - DeWalt DCED400 Instruction Manual

English
Charger Cleaning Instructions

WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.

Wall Mounting

Some D WALT chargers are designed to be wall mountable
E
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE

ASSEMBLY AND ADJUSTMENTS


WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Assembling the Pole (FIG. D, E)
1. To assemble the pole, line up the upper pole
lower pole as shown in Fig. D. Press down the latching
6
button and slide the upper pole into the lower pole.
17
Avoid pinching the wire. Ensure the latching button
engages the latch hole
2. Secure the poles by tightening the middle bolt
the supplied hex wrench
Attaching the Auxiliary Handle (Fig. F)
1. Place the auxiliary handle
so the upper pole 5 is between them.
2. Hold the auxiliary handle in place and slide the handle
bolts into the handle from the top, threading them
22
into the handle base.
3. Tighten the handle bolts with the supplied hex
wrench 20 . Ensure the handle is securely attached.
Adjustment (Fig. G)

WARNING:
personal injury, turn appliance off and remove
battery before making any adjustments or
removing/installing attachments or accessories.
10
Shock hazard. Disconnect the
To reduce the risk of serious
and the
5
18 .
19
20 as shown in Fig. E.
4 on top of the handle base
To reduce the risk of serious

WARNING:
Damage or personal injury could result.

WARNING:
APPLIANCE WITHOUT GUARD FIRMLY IN PLACE.
The guard must always be properly attached on the
appliance to protect the user.
The auxiliary handle
However, if adjustment is necessary, loosen the four bolts
with a hex wrench and slide the auxiliary handle up or down
the upper pole.
Cut Depth Adjustment (Fig. H)

WARNING:
APPLIANCE WITHOUT GUARD FIRMLY IN PLACE.
The guard must always be properly attached on the
appliance to protect the user.

WARNING:
guard 23
the small guard is located toward the bottom of the
depth adjustment wheel
the small guard is not in place.
The depth of cut can be adjusted to allow a deeper or
shallower cut, and to increase the life of the blade. There
are three adjustible settings that can be set using the depth
adjustment lever
1. Wait for blade to come to complete stop.
2. Remove the battery from the tool.
3. For a shallower cut, pull the depth adjustment lever away
from the housing and slide it down into one of the lower
depth adjustment slots
4. For a deeper cut, pull the depth adjustment lever away
from the housing and slide it upwards into one of the
upper depth adjustment slots
nOTE: Recommend 1.4" (3.5 cm) depth for edging.
with
5. Ensure the depth adjustment lever is fully seated in one
of the depth adjustment slots before using the tool.
nOTE: Thick overgrowth may drag on the guard. Reduce cut
21
depth to minimum to help reduce this effect.
Pull-Up Edge Guide (Fig. I, J)
The edge guide is useful for cutting a straight path along
sidewalks. For landscaping or trenching in the yard the edge
guide can interfere with moving the edger through hard soil
or sod. The edge guide
will also perform trenching or landscaping operations.
To Change Position of the Edge Guide
• To use without the edge guide, pull edge guide knob
away from the housing and slide the edge guide knob to
the upper guide notch
nOTE: In this position the edge guide is raised and the
blade can more easily trench or cut along the edges
Never remove the guard.
NEVER OPERATE
4 is positioned to maximize balance.
NEVER OPERATE
Do not use edger if the small
does not move when adjusting depth. Ensure
13 . Do not operate edger if
.
14
24 on the housing.
on the housing.
25
16 can be adjusted so that the edger
26 on the housing.
22
15