Summary of Contents for Vinten V4165-0002
- Page 1 User Guide Environmental Camera Enclosure Weatherproof camera enclosure Weatherproof camera enclosure, fan cooled Weatherproof camera enclosure with AC cooler www.vinten.com...
- Page 2 Copyright © 2020 All rights reserved. Original Instructions: English All rights reserved throughout the world. No part of this publication may be stored in a retrieval system, transmitted, copied or reproduced in any way, including, but not limited to, photocopy, photograph, magnetic or other record without the prior agreement and permission in writing of the Videndum Plc.
-
Page 3: Table Of Contents
Contents Safety and Warnings . . . . . . . . . . . . . . . . . . . . . . . . 2 Regular Checks. -
Page 4: Safety And Warnings
Safety and Warnings Important information on the safe installation and operation of This label V4165-2070 is to be fixed securely to side of the enclosure. the product . Read this information before operating the product . For your personal safety, read these instructions . Do not operate the product if you do not understand how to use it safely . -
Page 5: Health And Safety
Safety and Warnings Health and Safety Electrical Connections WARNING! Risk of personal injury or injury to WARNING! This product must be connected to a power supply of the same voltage (V) and current (A) as others . All personnel must be fully trained and adhere to indicated on the product and described in the Technical correct manual handling techniques and Health &... - Page 6 Safety and Warnings Mounting and Installation WARNING! When mounted at height it is recommended that secondary protection against falling is installed, such WARNING! Always ensure that all power and auxiliary as a net below the product or securing cables. These communications cables are routed so that they do not should be suitable of supporting the weight of the product present any danger to personnel.
-
Page 7: Intended Use
Intended Use Safety Notes for Operators This product is designed as a enclosure to protect a broadcast camera and lens for outdoor use. Operators must familiarise themselves with the working footprint of Operating Description the robotic head and enclosure, to prevent inadvertent collisions or injury to personnel. -
Page 8: Models
Models Enclosures Weatherproof camera enclosure, fan cooled The range of enclosures covers three models: IP65 rated Weatherproof camera enclosure IP63 rated Weatherproof camera enclosure, fan cooled IP65 rated Weatherproof camera enclosure with AC cooler Weatherproof camera enclosure with AC cooler Weatherproof camera enclosure... -
Page 9: External Components
External Components 1 ......... . Enclosure Lid 8 . -
Page 10: Installation
Installation • • Adjust the lock plate vertically on the rear of the enclosure to Adjust the lock plate vertically on the rear of the enclosure to Mounting Enclosure to Cradle Mounting Enclosure to Cradle ensure a good fit and tighten the hex screws. ensure a good fit and tighten the hex screws. -
Page 11: Mounting Camera & Skid Plate
Where will depend on the length of the lens. Long lenses, Connect the lens cables, and the Vinten data cable (Digital with need of support, must use the support post provided only for Fujion or Cannon Lenses) ensuring that the lens is on the skid. -
Page 12: Shorter Lenses
Installation Shorter lenses: Loose insulation is provided to fill in gaps where possible Where a short lens is being fitted, use slots in the skid plate to position once the camera is fitted. the camera forward in the enclosure. The PSU is to be moved to the rear mounting location and cable tied to the metal strap provided. -
Page 13: Cable Entry Box
Installation Installation Cable Entry Box: Apply DC4 compound (thick non setting silicone based grease) to the clamping area and sealant to the void. The DC4 helps fill any • • The cable entry box has provision for 4 cables: The cable entry box has provision for 4 cables: gaps when the neoprene foam is compressed. -
Page 14: Lid Closure And Sealing
Installation Apply DC4 and Sealant to top clamp piece and attach to base Lid Closure and Sealing: using screws. Avoid resting tools against lid seals. Avoid closing lid with wires or other items in the shut line. Inspect lid seal for contamination or damage before final closure. Setting Ensure all items and internal surfaces are completely dry. -
Page 15: Cooler Use
Installation Cooler Use: It is recommended that the thermostat is set no lower than 35˚C. Running the cooler in low temperature conditions will promote The cooler will maintain a temperature at least 10˚C below the condensation on the cooling plates and will operate the fans ambient air temperature outside under the following conditions: unnecessarily. -
Page 16: Optional Fan Speed Control
The Pump and wiper function are operated in the Vinten Robotics Controller (VRC) Software through the GPIO controls. The customer should take their own measurements if fan noise is particularly important and local conditions allow for reduced cooling effort. -
Page 17: Electrical Connections
Installation Electrical Connections Cable Management To ensure a safe and tidy installation, all cables connected to the WARNING! Ensure power is isolated before making any enclosure should be dressed and secured. connections. CAUTION! Leave sufficient slack in the cables between the fixed mounting and the head for free and full range of For IO function the head operates relays which close the user movement. -
Page 18: Maintenance
Maintenance Regular Checks Changing the Fuse Routine Use WARNING! Risk of electric shock. Disconnect the power cable. Fuses must only be changed During use, check the following regularly: by a trained and competent person. Check the integrity of bolts and fixings securing the enclosure to the support. -
Page 19: Troubleshooting
Troubleshooting Fault Check Cooler fan running all the time in cold Place thermostat within handle / above camera body. Set thermostat above 35˚C conditions Set thermostat to 35˚C, or preferred set point. Place thermostat within handle / above camera Cooler not operating body. -
Page 20: Specifications
Specifications Technical Specification Weatherproof Camera Enclosure External dimensions [L/W/H) 851 x 241 x 320 mm (33.5 x 9.5 x 12.6 in.) exc. sun shade Max camera/lens size 740 mm (29.1 in.) long [eg. Hitachi SK HD1200 with Fujinon UA46X] Weight 27 kg (59.5 lb) Temperature range +4°C to +55°C (+39°F to +131°F) Ambient (internal max 45˚C with cooler) -
Page 21: Compliance
Compliance Declaration of Conformity Waste of Electrical and Electronic Equipment (WEEE) Directive Videndum Production Solutions Ltd., as the (2012/19/EU) responsible party for regulatory compliance, declares under our sole responsibility that as delivered the This symbol marked on the product or its packing indicates that this described product has been assessed and product must not be disposed of with general household waste. - Page 22 Compliance FCC Declaration of Conformity This product complies with Part 15 of the FCC Rules. Operation is Weatherproof camera enclosure subject to the following two conditions: Weatherproof camera enclosure, fan cooled (1) This product may not cause harmful interference. Weatherproof camera enclosure with AC cooler (2) This product must accept any interference received, including interference that may cause undesired operations.
- Page 24 Publication No. V4164-4981/1 www.vinten.com...
Need help?
Do you have a question about the V4165-0002 and is the answer not in the manual?
Questions and answers