XPLORE TECHNOLOGIES iX104C6 Quick Start Manual

OPEN ME FIRST
OPEN ME FIRST
1
1

Unpacking the Tablet

This document assists you with the
setup and basic operation of your
Make sure your package includes the following items.
new rugged tablet computer.
(NOTE: Your project team may remove items that you do not need.
If items are missing, contact your project team leader.)
The iX104C6 User's Handbook
contains complete information and
• Tablet computer
is located on the tablet's hard disk.
• Battery pack
To access the handbook, click Start;
• Stylus (pen) with tether
then select the Xplore option from
attached to the tablet computer
the menu. The handbook opens and
• AC adapter
displays the Table of Contents.
• Power cord
• Warranty information card
• Declaration of Conformity
• Cleaning cloth
The AC adapter is 19V, 3.42A. See the iX104C5 User's Handbook, for
safety instructions regarding the AC adapter and operation of the tablet.
3
5
Adjusting the
Screen Brightness
To adjust the screen brightness,
click the power management icon
on the Windows taskbar; then
select Adjust screen brightness.
Power management icon
Adjust slider bar in power options
menu to change screen brightness.
iX104C6
iX104C6
Quick Start Guide
Quick Start Guide
2

Installing the Battery Pack

Unpacking the Tablet
1. Orient the battery with the slides in the empty
Make sure your package includes the following items.
battery tray.
(NOTE: Your project team may remove items that you do not need.
If items are missing, contact your project team leader.)
2. Slide the battery into the tray and press it firmly
until it is seated.
• Tablet computer • Warranty information card
3. The battery release latch will slide to its original
• Battery pack • Declaration of Conformity
position. The lock button pops back into the locked
• • Cleaning cloth
Stylus (pen) with tether
position, securing the battery in place.
attached to the tablet computer
• AC adapter
• Power cord
The AC adapter is 19V, 3.42A. See the iX104C5 User's Handbook, for
safety instructions regarding the AC adapter and operation of the tablet.

Charging the Battery

Your battery ships with some level of charge, but Xplore Technologies recommends
that you fully charge the battery before first use. Charging the battery typically
6
takes 1.5 to 2.5 hours (depending on the size of the battery included with your
computer).
Calibrating the Digitizer
and Touch Panel
To charge the battery while it is installed in the computer:
Connect an approved power source,
Calibrate the digitizer and touch panel when you
such as an AC adapter or cigarette
use the tablet for the first time.
lighter adapter (CLA), to the power
port on the tablet.
1. Click
Start > Control Panel.
2. In the Control Panel, select
Hardware and Power port
When the power source is connected
.
Sound
to the wall socket or vehicle socket,
3. Click .
the battery begins charging and the Tablet PC Settings
Status LED flashes green.
4. Click Calibrate .
5. Click Pen input.
The charging process continues until
6. Click Calibrate.
the battery charge reaches 100%,
at which point the Status LED glows
7. Click Touch input.
solid green.
8. Click Calibrate.
9. When you finish calibrating the digitizer and
touch panel, click .
OK
3
2
Charging the Battery
Installing the Battery Pack
Your battery ships with some level of charge, but Xplore Technologies recommends
that you fully charge the battery before first use. Charging the battery typically
1. Orient the battery with the slides in the empty
takes 1.5 to 2.5 hours (depending on the size of the battery included with your
battery tray.
computer).
2. Slide the battery into the tray and press it firmly
until it is seated.
To charge the battery while it is installed in the computer:
3. The battery release latch will slide to its original
Connect an approved power source, position. The lock button pops back into the locked
such as an AC adapter or cigarette position, securing the battery in place.
lighter adapter (CLA), to the power
port on the tablet.
When the power source is connected
to the wall socket or vehicle socket,
the battery begins charging and the
Status LED flashes green.
4
The charging process continues until
Turning On the
the battery charge reaches 100%,
at which point the Status LED glows
Computer
solid green.
1. Make sure the battery is charged or
that the tablet is plugged into an
external power source.
7
2. Press the Power (ON/OFF)/
Backlight (ON/OFF)/Resume
Using The Pen
button.
To perform this function...
Select an object (left button click)
Perform a double-click
Perform a right-click
Power (ON/OFF)/Backlight
Status LED
(ON/OFF)/Resume button
Right-click icon
Move or drag an object
WARNING: Do not use items such as a ball point pen or a screwdriver that can
damage the computer. Damage caused by using an item not provided with the tablet
is not covered by the tablet warranty.
4
Power port
Status LED
5
Adjusting the
Screen Brightness
To adjust the screen brightness,
click the power management icon
on the Windows taskbar; then
select Adjust screen brightness.
Do this
Tap the pen tip once on the object.
Quickly tap the pen tip twice on the object.
Touch mode: In the Windows taskbar, press the right-click
Power management icon
icon; then click the object.
Active mode: Hold the pen or your finger directly on the object
for 1 second. The right-click icon appears.
or
Press the right-click button on the pen while you click the object.
Adjust slider bar in power options
menu to change screen brightness.
Place the pen tip or your finger on the object; continue to hold the
pen tip or your finger against the screen as you move the pen.
Turning On the
Computer
1. Make sure the battery is charged or
that the tablet is plugged into an
external power source.
2. Press the Power (ON/OFF)/
Backlight (ON/OFF)/Resume
button.
Power (ON/OFF)/Backlight
(ON/OFF)/Resume button