Advertisement
Quick Links
T
ECHNICAL INFORMATION
Model No.
Description
C
ONCEPT AND MAIN APPLICATIONS
Models MT690/ MT691 are the first 14.4V/ 18V maktec cordless impact drivers
powered by 1.1Ah Li-ion batteries L1451/ L1851 designed to provide
the cost advantage.
These products are available in the following variations.
MT690
Model No.
Charger
MT690Z
No
MT690E
DC1851
MT691
Model No.
Charger
MT691Z
No
MT691E
DC1851
S
pecification
Specification
Voltage: V
Capacity: Ah
Battery
Cell
Energy capacity: Wh
Charging time: min.
Max output: W
No load speed: min.
ˉ
Impacts per minute: min.
Driving shank
Max. fastening torque
Machine screw
Standard bolt
Capacities
High tensile bolt
Coarse thread
Electric brake
Torque adjustment
Variable speed control
Reversing function
LED Job light
Weight according to
EPTA-Procedure 01/2003
: Torque at 3 seconds after seating, when fastening M14 high tensile bolt
*1
: MT690/with battery L1451, MT691/with battery L1851
*2
S
tandard equipment
See the model variation list above.
Note: The standard equipment for the tools may vary by country.
O
ptional accessories
Charger DC1851
Li-ion battery L1451 (for MT690 only)
Li-ion battery L1851 (for MT691 only)
MT690/ MT691
Cordless Impact Driver
Battery
Battery
Type
Quantity
cover
No
No
L1451
2
Battery
Battery
cover
Type
Quantity
No
No
L1851
2
Model
¹=rpm
¹=ipm
ˉ
: N.m [ kgf.cm] (in.lbs)
*1
(length)
*
: kg (lbs)
2
Plastic
carrying case
No
No
1
Yes
Plastic
Phillips
carrying case
bit 2-65
No
No
No
1
Yes
No*
*
Yes for Taiwan
1:
MT690
14.4
1.1
Li-ion
16
60 with DC1851
230
0 - 2,400
0 - 3,000
6.35mm (1/4") Hex
130 [1,330] (1,150) 135 [1,380] (1,200)
M4 - M8 (5/32" - 5/16")
M5 - M14 (3/16" - 9/16")
M5 - M12 (3/16" - 1/2")
22mm - 125mm (7/8" - 4-7/8")
Yes
No
Yes
Yes
No
1.4 (3.1)
W
The image above is MT691.
Dimensions: mm (")
Length (L)
Width (W)
Height (H)
Hook
No
No*
1
1
MT691
18
20
1.5 (3.2)
PRODUCT
P 1/ 8
L
H
173 (6-13/16)
82 (3-1/4)
225 (8-7/8)
Advertisement
Related Manuals for Makita maktec MT690Z
Summary of Contents for Makita maktec MT690Z
- Page 1 ECHNICAL INFORMATION PRODUCT P 1/ 8 Model No. MT690/ MT691 Description Cordless Impact Driver ONCEPT AND MAIN APPLICATIONS Models MT690/ MT691 are the first 14.4V/ 18V maktec cordless impact drivers powered by 1.1Ah Li-ion batteries L1451/ L1851 designed to provide the cost advantage.
-
Page 2: Necessary Repairing Tools
Retaining ring S and R pliers removing Ring spring 11 of Bit holder section [2] LUBRICATION Apply Makita grease N. No.2 to the following portions designated with the black triangle to protect parts and product from unusual abrasion. Item No. - Page 3 P 3/ 8 epair [3] DISASSEMBLY/ASSEMBLY [3] -1. DC Motor DISASSEMBLING (1) Disassemble DC motor as drawn in Fig. 2. Fig. 2 1. Remove Hammer case and 2. Remove Housing R from Housing L 3. Remove DC motor together Hammer section from Housing by unscrewing eight 3x16 Tapping with Internal gear case from set by unscrewing four 4x25...
- Page 4 P 4/ 8 epair [3] DISASSEMBLY/ASSEMBLY [3] -2. Anvil, Bit Holder Section DISASSEMBLING (1) Remove Hammer case and Hammer section from Housing set as per the left drawing in Fig. 2. (2) Disassemble Bit holder section and Anvil as drawn in Figs. 5 and 6. Fig.
- Page 5 P 5/ 8 epair [3] DISASSEMBLY/ASSEMBLY [3] -3. Hammer Section DISASSEMBLING (1) Remove Hammer case and Hammer section from Housing set as per the left drawing in Fig. 2. (2) Disassemble Hammer section as drawn in Figs. 7, 8, 9 and 10. Fig.
- Page 6 P 6/ 8 epair [3] DISASSEMBLY/ASSEMBLY [3] -3. Hammer Section (cont.) ASSEMBLING Assemble Hammer section by reversing the disassembly procedure. Refer to Figs. 11, 10, 9 and 8. Before putting Flat washer 24 in Hammer (Refer to Fig. 10), make sure that twenty-four Steel balls 3.5 are put in the groove of Hammer as shown in Fig.
-
Page 7: Circuit Diagram
P 7/ 8 ircuit diagram Fig. D-1 Color index of lead wires' sheath Black Yellow Red dot mark DC motor LED job light Line filter Line filter is not used for some countries. Switch Terminal... -
Page 8: Wiring Diagram
P 8/ 8 iring diagram Fig. D-2 Fig. D-3 Wiring to Terminal Wiring to DC motor The Flag connector has to be connected Connect Lead wire (red) receptacle to the so that its wire connecting portion is located terminal with Red dot mark and Lead wire over (+), (-) pole marks.