Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for THK SVS-Vistek CoaXPress EoSens 3CXP
- Page 1 EoSens® 3CXP User Guide...
-
Page 2: Table Of Contents
Contents Before you start About this manual 1.1.1 Tips, remarks, and notes 1.1.2 Registered trademarks 1.1.3 Conformity and use 1.1.4 Supplements Warranty and non-warranty clause Support Introduction Intended use Scope of delivery Optional accessories System requirements The camera Camera description Operating temperature Additional cooling Interfaces of the camera... - Page 3 Camera dimensions Spectral response 5.5.1 Monochrome and color with UV/IR Cut Filter 5.5.2 Monochrome and color without UV/IR Cut Filter Appendix Declaration of Conformity...
- Page 4 Figures Fig.: 3-1: Interfaces of the camera EoSens® 3CXP Fig.: 4-1: Connecting input and output signals with the internal circuit Fig.: 4-2: IO signals Fig.: 4-3: Connecting camera and image processing system Fig.: 5-1: Rear view Fig.: 5-2: Side view with C-mount adapter Fig.: 5-3: Side view with F-mount adapter Fig.: 5-4: Quantum Efficiency mono and color with UV/IR Cut Filter Fig.: 5-5: Quantum Efficiency mono and color without UV/IR Cut Filter...
-
Page 5: Before You Start
Before you start About this manual This manual contains helpful information to install and operate the described cam- era. It has been produced with care. Nevertheless, information might be erroneous or incomplete. Mikrotron GmbH cannot be held responsible for any problems resulting from incomplete or erroneous information. -
Page 6: Supplements
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions given in this guide, may cause harmful interference to radio communications. Operation of this equipment in a res- idential area is likely to cause harmful interference in which case the user will have to correct the interference at its own expense. -
Page 7: Warranty And Non-Warranty Clause
Life support applications The products described in this manual are not designed for use in life support appli- ances or devices and systems where malfunction of these products can reasonably be expected to result in personal injury. NOTICE Mikrotron customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Mikrotron for any damages res- ulting from such improper use or sale. -
Page 8: Introduction
Introduction Intended use The camera EoSens® 3CXP belongs to the product class of so-called high-speed machine vision (MV) cameras that are integrated into test or measurement systems. High-speed MV cameras are designed to capture images with high frame rate for various purposes in an industrial or scientific environment to deliver image data for further analysis. -
Page 9: System Requirements
Cables The four bundle cable KKRDDINDINxx/6Gx4 with DIN 1.0/2.3 connector at both ends (4x) is available in lengths of 5 m, 10 m, 15 m, or 20 m. It is used to connect the frame grabber and camera when both are equipped with DIN 1.0/2.3 connectors. -
Page 10: The Camera
The camera Camera description All cameras of the EoSens CXP family are CoaXPress compliant. The high-speed CMOS cameras come with a 3.0 Megapixel sensor of 1696 x 1710 (H x V). They are widely configurable and scalable to fit your needs and are available in monochrome and color (Bayer filter). -
Page 11: Operating Temperature
Operating temperature Despite of its high performance, the fanless 3CXP camera is compact and works silently. If the camera is mounted on mechanical parts, the heat generated during operation will be dissipated by the cooling fins at the rear of the camera and the mechanical parts. -
Page 12: Interfaces Of The Camera
Interfaces of the camera Fig.: 3-1: Interfaces of the camera EoSens® 3CXP 1 Status LED to verify the operating status of the camera 2 CoaXPress DIN1.0 / 2.3 connector used to connect the camera with a CoaXPress compliant frame grabber. 3 12 pin Hirose power connector used when an external power supply (12 …... -
Page 13: Status Led
Status LED The multi-color status LED indicates camera and connection states. LED State Indication No power Solid orange System is booting Slow pulse red Powered, but nothing connected (not applicable if PoC is used) Fast flash alternate Connection detection in progress, PoC active green/orange Fast flash orange Connection detection in progress, PoC not in use... -
Page 14: First Steps
First steps Connecting a frame grabber The CoaXPress standard describes seven connections for data transmission between camera and frame grabber. The transmission speed of the camera can either be set to 1.25, 2.5, 3.125, or Gb/s. 5 The possible cable length depends on the cable type used, its quality, and the selected transmission speed. -
Page 15: Connecting An External Power Supply Or I/O Signals
INFO All connections are hot-pluggable. The assignment of the DIN cables KKRDDINDINxx/6Gx4 and KKRDDINBNCxx/6Gx4 connector pins is as follows: DIN connector Frame grabber Cable color 1 (triangle) TX channel 0 2 TX channel 1 Green 3 TX channel 2 Blue 4 TX channel 3 Yellow Connecting an external power supply or I/O signals... -
Page 16: Fig.: 4-1: Connecting Input And Output Signals With The Internal Circuit
Signal Signal 1 + 12 2 + 11 VCC (12 - 24 V) OUT1 OUT0 Internally connected with: pin 4 pin 8 pin 6 pin 10 connected with pin 3 + 5 Fig.: 4-1: Connecting input and output signals with the internal circuit All inputs accept 3.3 ... -
Page 17: Connecting Camera And Image Processing System
NOTICE This circuit will invert the signal. (A high level at the input will be seen as low level at the camera.) Examples for R1 Input voltage Resistor 3.3 V 2.7 kOhm 4.7 kOhm 12 V 12 kOhm 24 V 22 kOhm Connecting camera and image processing system To make use of the full performance, all cables, connectors and the frame grabber... -
Page 18: The Power-Up Profile
8. If an external power supply (7) is used, connect the power supply with the main supply. 9. Switch on the image processing system (1). 10. Check the status LED of the camera to verify that the camera is ready for use. The power-up profile If the camera is powered-up, the power-up profile permanently stored in the non- volatile memory of the camera will be loaded. - Page 19 1. Open the tool “CXP Updater.exe” in the folder “Firmware”. 2. Select the CTI file that corresponds to the frame grabber board. If unsure, con- sult the Device Manager. 3. To add a CTI file that is not in the list, select Add another CTI file and navigate to the file.
-
Page 20: Technical Data
Technical data Camera specifications Frame rate (8 bit) max. 225000 fps Pixel depth 8 bit Shutter speed 1 µs – 1 s Shutter time (steps) 1 µs Max. Jitter ±4 ns Max. Trigger fre- 300 kHz quency Quantum efficiency 37% @ 680 nm Interfaces CoaXPress 1.x @ 1,25 Gb/s CoaXPress 1.x @ 2,5 Gb/s... -
Page 21: Sensor Specifications
Sensor specifications Sensor type CMOS, monochrome or RGB (Bayer Filter) Image sensor size 13.57 x 13.68 mm Resolution 1696 x 1710 px Pixel depth 8 bit Pixel size 8 x 8 µm Active area 13,57 x 13,68 mm ROI min. 128 x 2 px Fill factor 36 %... -
Page 22: Fig.: 5-1: Rear View
Fig.: 5-1: Rear view 11,6 Fig.: 5-2: Side view with C-mount adapter 5 Technical data... -
Page 23: Fig.: 5-3: Side View With F-Mount Adapter
45,5 Fig.: 5-3: Side view with F-mount adapter Spectral response 5.5.1 Monochrome and color with UV/IR Cut Filter Fig.: 5-4: Quantum Efficiency mono and color with UV/IR Cut Filter 5 Technical data... -
Page 24: Fig.: 5-5: Quantum Efficiency Mono And Color Without Uv/Ir Cut Filter
5.5.2 Monochrome and color without UV/IR Cut Filter Fig.: 5-5: Quantum Efficiency mono and color without UV/IR Cut Filter 5 Technical data... - Page 25 Appendix The following page contains the Declaration(s) of Conformity. 6 Appendix...
- Page 26 EU Declaration of Conformity EU-Konformitätserklärung Mikrotron GmbH Phone: +49 (0)89 72634200 Landshuter Str.20-22 Fax: +49 (0)89 726342-99 D-85716 Unterschleissheim Mail to: info@mikrotron.de www.mikrotron.de We herewith declare under our sole responsibility that the products mentioned below: Hiermit erklären wir in alleiniger Verantwortung, dass die folgenden Produkte: Product type: 3CXP Camera Produkt:...
- Page 27 SVS-Vistek GmbH Ferdinand-Porsche-Str. 3 82205 Gilching Phone: +49 8105 3987-60 https://www.svs-vistek.com info@svs-vistek.com © 09-2022 This document and the product(s) described are subject to change without further notice.
Need help?
Do you have a question about the SVS-Vistek CoaXPress EoSens 3CXP and is the answer not in the manual?
Questions and answers