Related Manuals for ADC FlexWave nano
Summary of Contents for ADC FlexWave nano
- Page 1 Confidential 8/11/2008 Mobile Network Solutions FlexWave™ BSS FlexWave™ nano Hardware Installation AGCP ADCP 75-313 • Issue 2 • 07/2008 D-620056-0-20, Rev A © 2008 ADC Telecommunications, Inc. Page 1...
- Page 2 DISCLAIMER OF LIABILITY Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages...
- Page 3 DISPOSAL OF ELECTRONIC AND ELECTRICAL WASTE Pursuant to the WEEE EU Directive electronic and electrical waste must not be disposed of with unsorted waste. Please contact your local recycling authority for disposal of this product. © 2008 ADC Telecommunications, Inc. Page 3...
-
Page 4: Table Of Contents
Chassis Bond Strap – Multi-TRX only............14 Mounting the FlexWave™ nano..............16 Mounting Multi-TRX FlexWave™ nano ............18 Mounting Multi-TRX 165 FlexWave™ nano ........... 18 Initial Frequency Calibration..............19 LED Status Indicators................20 Annex A – Drawing 165#018 ..............22 © 2008 ADC Telecommunications, Inc. Page 4... -
Page 5: Introduction
Confidential 8/11/2008 1 Introduction 1.1 Purpose and Scope This document describes the procedure used to install the FlexWave™ nano hardware and physical connections together with applying the base software configuration. © 2008 ADC Telecommunications, Inc. Page 5... -
Page 6: Warnings
Confidential 8/11/2008 2 Warnings Please refer to the appropriate section of ADCP-75-311 [1]. © 2008 ADC Telecommunications, Inc. Page 6... -
Page 7: Regulatory Information
Confidential 8/11/2008 3 Regulatory Information For all regulatory information please see ADCP-75-311 [1]. © 2008 ADC Telecommunications, Inc. Page 7... -
Page 8: Unpacking
4 Unpacking Unpack FlexWave™ nano and check to see that the unit has not been damaged in transit. Any damaged units should be returned to your supplier. Figure 1 - Unpacking the FlexWave™ nano © 2008 ADC Telecommunications, Inc. Page 8... -
Page 9: Fitting The External Antenna Kit (Optional)
A n te n n a C o v e r B o tto m Figure 2 - Removal of antenna covers Remove the antenna cover body, by unscrewing the two Torx T20 screws retaining © 2008 ADC Telecommunications, Inc. Page 9... -
Page 10: 165 Hardware
Network Listen (NWL) antenna is top right. To fit external antennas, remove the plastic cover from the unit and unscrew the the antennas to expose the SMA connectors. Connect directly to these connectors. © 2008 ADC Telecommunications, Inc Page 10... - Page 11 Confidential 8/11/2008 Removable Antennas Figure 5 - 165 FlexWave™ nano Removable Antennas © 2008 ADC Telecommunications, Inc. Page 11...
-
Page 12: Cabling The Flexwave™ Nano
NWL Port Secondary TX location See 7.2 Status Indicat RX Port TIB out TX Port TIB in 48v DC Powered Chassis USB Port Power Ethernet Bond (Not Figure 7 – 165 FlexWave™ nano Connections © 2008 ADC Telecommunications, Inc. Page 12... -
Page 13: Ethernet
Each 139/140/178 FlexWave™ nano must be connected to an Ethernet switch or hub via either a 109 ADC single power inserter or 126 ADC Powered Ethernet Switch. Refer to CENG0033 for details of the power supply connections. The 165 EDGE FlexWave™... -
Page 14: Chassis Bond Strap - Multi-Trx Only
Chassis Bond Point Figure 10 – Chassis Bond Screw Location – 139/140 BTS Connect the other end of the Chassis Bond lead to the next FlexWave™ nano chassis bond point in the chain. © 2008 ADC Telecommunications, Inc. Page 14... - Page 15 Confidential 8/11/2008 Chassis Bond Point Figure 11 – Chassis Bond Screw Location – 165 BTS © 2008 ADC Telecommunications, Inc. Page 15...
-
Page 16: Mounting The Flexwave™ Nano
(at least 80mm from the bracket to the top of wall and 120mm from the side of the bracket to a side wall). See the diagram below, Figure 13 - Fixing the wall bracket. 80m m m in 120m m m in Figure 13 - Fixing the wall bracket © 2008 ADC Telecommunications, Inc. Page 16... - Page 17 MUST be uppermost. Once the unit has been attached to the bracket the outer cover MUST be removed to expose the cooling vanes, as shown in Figure 15 - Ceiling Mounted FlexWave™ nano Figure 15 - Ceiling Mounted FlexWave™ nano © 2008 ADC Telecommunications, Inc. Page 17...
-
Page 18: Mounting Multi-Trx Flexwave™ Nano
Remove the plastic cover from the top unit and attach it to the bottom unit • Attach the Ethernet and TIB cables to the top unit • Replace the plastic cover on the top unit © 2008 ADC Telecommunications, Inc. Page 18... -
Page 19: Initial Frequency Calibration
Once the test completes then the calibration is completed and the procedure should be repeated for all installed FlexWave™ nano before reconnecting the TIB cables. Following the 24-hour period, the Frequency Calibration procedure should be performed as per the Operations procedure – Ref {2} © 2008 ADC Telecommunications, Inc. Page 19... -
Page 20: Led Status Indicators
Alternating The unit is in the fast Green / calibrating state Orange [SYNC]. Slow Blink LED_NOT_TRANSMITTING Green The radio carrier is Slow Flash not being transmitted. LED_OPERATIONAL Green Default condition if 12 (Low) © 2008 ADC Telecommunications, Inc. Page 20... - Page 21 Confidential 8/11/2008 Steady none of the above apply. © 2008 ADC Telecommunications, Inc. Page 21...
-
Page 22: Annex A - Drawing 165#018
Confidential 8/11/2008 10 Annex A – Drawing 165#018 © 2008 ADC Telecommunications, Inc. Page 22... - Page 23 ADCP Number: Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages.
Need help?
Do you have a question about the FlexWave nano and is the answer not in the manual?
Questions and answers