Summary of Contents for Rapid Marine Sea-Doo RTX 230
- Page 1 Hold Up An adjustable lifting sling for PWC’s that won’t let you down for the perfect fit www.rapidmarine.co.uk...
- Page 2 Contents Contents Disclaimer Proof Load Test Operating Instructions The Kit Attachment Bracket Positioning Fitting The Brackets Attaching the Sling rapidmarine.co.uk e: sales@rapidmarine.co.uk...
- Page 3 Read the instructions thoroughly. They have been written to help you install the attachment brackets and the lifting sling safely and correctly. Rapid Marine Limited cannot accept any responsibility for damage to your PWC, yourself or any third party by incorrect use of these instructions.
- Page 4 Proof Load Testing Rapid Marine Limited recommend that once the brackets are fitted, an independent proof load test be carried out by a recognised test centre (see table below) rapidmarine.co.uk e: sales@rapidmarine.co.uk...
- Page 5 Operating Instructions Always Store and handle the sling correctly. ■ Inspect the sling and fitting before use and before putting ■ into storage. Ensure the sling is securely attached to the PWC. ■ Ensure the PWC is balanced and will not tilt or fall. ■...
- Page 6 This product is not designed for, or to be used for “man riding” IMPORTANT If for any reason any of the ATTACHMENT HANDLES do not engage correctly, DO NOT under any circumstances lift the PWC and report this to a competent person. Operative Training The sling should only be used by trained operatives.
- Page 7 Operating Instructions Before Use The sling is to be inspected for any defects and to ensure ■ the identification and specifications are correct. If the sling is unidentified or defective, it should not be used ■ but should be reported to a competent person. All fixtures and fittings should be checked to ensure they are ■...
- Page 8 The Kit Your Rapid Marine PWC Adjustable Lifting Sling Kit consists of 1 x Fixing Bag containing 1 x Drill Bag containing 10 x Nuts 1 x Template plug 10 x Bolts 1 x 3mm drill bit 10 x Anti Vibration Washers...
- Page 9 Innovative accessories for tenders and jetskis Attachment Bracket Positioning Attachment Bracket Positioning e: sales@rapidmarine.co.uk | t: 00 44 (0)1752 401 111 Innovative Lifting Sling Kits for Seadoo for tender Bracket positioning for all models with the new ST3 hull Models with ST3 Hull e: sales@rapidmarine.co.uk | t: MODELS RXT 230 - RXT X 300...
- Page 10 Attachment Bracket Positioning Attach the brackets (A+B) in the correct position as illustrated. This will ensure the black bungee elastic is tight and the attachment handles face inwards and do not rotate if hit by a wave when lifting. It is important to ensure the attachment handles are facing in the correct direction before lifting.
-
Page 11: Fitting The Brackets
Fitting The Brackets STEP 1 Insert the template plug into a bracket and then place it in the correct position, with the key hole in line with the mark on the tape. STEP 2 Holding the bracket up tight to the underneath of the moulding, use the 6mm drill bit to make a hole, being careful... - Page 12 Fitting The Brackets STEP 5 Using the 3mm drill bit, make a pilot hole through the template plug. STEP 6 Remove the bracket revealing the 3 holes. STEP 7 Using the 22mm drill bit, make a hole about 8mm deep in the 3mm pilot hole.
- Page 13 Fitting The Brackets Step 9 You need to check the hole has been drilled deep enough. Replace the bracket and push the 6mm bolts into the holes without attaching the nuts. STEP 10 Insert the attachment handle ensuring it is a tight fit to the attachment bracket.
- Page 14 Attaching The Sling Attaching The Sling Each leg of the sling is colour coded Port (RED) and Starboard Each leg of the sling is colour coded Port (RED) and Starboard (GREEN) and marked Forward (FWD) and Aft (AFT) to ensure it (GREEN) and marked Forward (FWD) and Aft (AFT) to ensure it is attached in the correct position.
- Page 15 www.rapidmarine.co.uk Ring Ring Assembly Assembly Lay the sling over the PWC with the RING ASSEMBLY on the seat and each Lay the sling over the PWC with the RING ASSEMBLY on the leg of the sling in the correct position. seat and each leg of the sling in the correct position.
- Page 16 MANUFACTURED IN THE UK...
Need help?
Do you have a question about the Sea-Doo RTX 230 and is the answer not in the manual?
Questions and answers