Summary of Contents for Autowel NICE-50MPAW
- Page 4 - Plasma Welding machines from Autowell's NICE SERIES fall into a category of Digital controlled ones. - The Graphic Type TOUCH PANEL system integrated therein enables it easy to operate. Forty welding conditions can be stored in memory. Designed and made in line with human body engineering in consideration of users' safeties and conveniences.
- Page 5 Model NICE- 50PAW NICE- 100PAW NICE- 200PAW NICE- 300PAW ￠ ￠ ￠ ￠ 3 , 220V, 3 , 220V, 3 , 220V, 3 ,220V, Primary Input Voltage 50/ 60Hz 50/ 60Hz 50/ 60Hz 50/ 60Hz Input Rating(KVA) Rated Output Current(A) Rated Maximum 50A, 100% 100A, 100%...
- Page 7 1). Power Switch 1). Power Switch 1). Power Switch 1). Power Switch - Power ON- OFF safety breaker ; SWITCH- ON supplies power. 2). Gas Flow Meter 2). Gas Flow Meter 2). Gas Flow Meter 2). Gas Flow Meter 2)- 1. PILOT GAS FLOW METER(ARGON GAS) - It functions to measure flowing volume of PILOT(Center Gas) supply during welding works.
- Page 8 allow leakage of cooling water. 8). MAIN POWER(- ) (WARNING) 8). MAIN POWER(- ) (WARNING) 8). MAIN POWER(- ) (WARNING) 8). MAIN POWER(- ) (WARNING) - So as to prevent incidental electricity shock, wiring work is allowed only after the power has been turned off.
- Page 9 3- 3 REAR SIDE NOMENCLATURE 3- 3 REAR SIDE NOMENCLATURE 3- 3 REAR SIDE NOMENCLATURE 3- 3 REAR SIDE NOMENCLATURE...
- Page 10 3- 4 Descriptions of Rear Side Nomenclatures 3- 4 Descriptions of Rear Side Nomenclatures 3- 4 Descriptions of Rear Side Nomenclatures 3- 4 Descriptions of Rear Side Nomenclatures POWER INPUT TERMINAL BOX (DANGER) - Working in flow of electricity may result in an incidental death by electricity shocks.
- Page 11 5). COOLING FAN 5). COOLING FAN 5). COOLING FAN 5). COOLING FAN - This fan functions to blow out inner heats of welding machine. - Long- time- accumulated- dusts inside welding machine may diminish cooling effects. - At least more than once a month, it is required to clean out accumulated dusts using compressed airs.
- Page 12 4. Manipulation and Operation 4. Manipulation and Operation 4. Manipulation and Operation 4. Manipulation and Operation 1). ERROR DISPLAY LAMP 1). ERROR DISPLAY LAMP 1). ERROR DISPLAY LAMP 1). ERROR DISPLAY LAMP - Three signaling lamps namely TEMP, GAS and WATER will flicker to signalize errors upon occurrence.
- Page 13 2)- 1. this displayer shows welding condition models covering 0 through 20. 20 welding conditions can be set up for each switch respectively of HIGH and LOW in CURRENT SELECT, in total 40 welding conditions can be set. 2)- 2. This displayer shows welding data.
- Page 14 - With this switch on, PILOT and SHIELD GAS can be checked. - Turning this switch on, adjust the KNOB of the PILOT, SHIELD GAS METER to get flowing volume as desired. - This switch must stand off during welding work. 5).
- Page 15 CARE FOR SAFETY. CARE FOR SAFETY. CARE FOR SAFETY. The Plasma welding machine of Autowel has been designed and made in full regards to safety matters. Nonetheless for the most sake of safety it is users themselves who are to bear always in minds safety matters.
-
Page 16: Installation
Check up conditions of Product. Check up conditions of Product. Check up conditions of Product. Check up conditions of Product. 1. In receipt of delivery of the product, please check thoroughly with it as to there being any damages or missing »p »p »p »p WARNING WARNING WARNING... - Page 17 1. During a time of electric current or operation, never open the cover of welding machine or it may cause incidental electricity shock. 2. Even when power is off, unless you are doing inspection of wiring works, do not open cover of terminals as like cooling water control device.
- Page 18 In changing welding condition or welding point while welding is under way, never forget to wear safety glass for protection from arc flash. As regards filtering color glass(BS 679) for protection from infrared and ultraviolet radiation, please refer to the eligible range as follows.
Need help?
Do you have a question about the NICE-50MPAW and is the answer not in the manual?
Questions and answers