Advertisement
1.3.5. DO regularly inspect power supply leads, plugs and sockets for wear, damage or loose connections.
1.3.6. DO check that the voltage marked on the product is the same as the power supply to be used and check that all fused plugs are fitted with
the correct capacity fuse.
1.3.7. DO NOT pull or carry the appliance by attached leads.
1.3.8. DO NOT pull plug from socket by the power cable.
1.3.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace,
or have repaired, by qualified persons. A U.K. 3 pin plug with ASTA/BS approval
is fitted. In case of damage, cut off and fit a new plug according to the following
instructions (UK only - see diagram right).
a) Ensure the unit is correctly earthed via a three-pin plug.
b) Connect the Green/Yellow earth wire to the earth terminal ‘E’.
c) Connect the Brown live wire to live terminal ‘L’.
d) Connect the Blue neutral wire to the neutral terminal ‘N’.
e) Ensure cable outer insulation extends past cable clamp and that clamp is tightened.
1.4.
THE 15 MINUTE RAPID BATTERY CHARGER SAFETY INSTRUCTIONS.
WARNING! DO NOT attempt to charge any battery other than that supplied for the drill. Other types of batteries may explode!
F
All mains electrical supply safety features must be followed as described in 1.3. above.
!
p
Disconnect the charger from the mains power supply when not in use.
!
DO NOT charge battery if room temperature is below 41
%
DO NOT expose the charger to damp or wet conditions.
%
DO NOT pull or carry the charger by the power lead.
%
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take charger to an authorised agent.
%
DO NOT dismantle the charger as this may cause damage or personal injury and will invalidate your warranty.
%
DO NOT insert foreign objects or material into the hole reserved for the battery pack.
%
DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat the charger. Allow the unit
%
to cool for 15 minutes before charging the next pack.
DO NOT attempt to connect two chargers together.
%
Store the charger in the same manner as battery pack in 1.2.
!
2.
SPECIFICATIONS
Chuck size . . . . . . . . . . . . . . . . . . . .10mm
Motor . . . . . . . . . . . . . . . . . . . . . . . . .12V
No Load Speed . . . . . . .0-380, 0-1400rpm
Impact Rate . . . . . . . .0-3040, 0-11200bmp
Capacity in wood . . . . . . . . . . . . . . .23mm
Capacity in Metal . . . . . . . . . . . . . . .16mm
Capacity in Concrete . . . . . . . . . . . .12mm
Wood Screw Capacity . . . . . . . . .5x50mm
Chuck size . . . . . . . . . . . . . . . . . . . .10mm
Max Torque . . . . . . . . . . . . . . .150kg/cm2
Battery Pack . . .12V (Model No CB12NTC)
Charger Pack 12V (Model No CPX12/NTC)
3. OPERATING INSTRUCTIONS
Note: When new, the battery pack will have been shipped in a low charge state. It will take longer to charge initially, and several subsequent charges
may also take a little longer than when the battery pack reaches its optimum performance. For the first charge remove batter pack from case
and charge as below:
3.1.
CHARGING THE BATTERY PACK (See figure 3 for LED diagram).
3.1.1. To remove the battery pack (fig1.7) from the drill, depress the two side release clips (fig.1. 8).
F
WARNING! Do not touch the metal terminals.
3.1.2. Place drill in carrying case and remove the battery charger (fig 2).
p
3.1.3. When you switch the charger on a “Bi” sound will be emitted.
3.1.4. The Charger will then be on STAND BY indicated by the Green LED blinking slowly. This means charger
is “standing by” ready to receive battery.
3.1.5. CHARGING. The battery pack and charger have the positive (+) and negative (-) terminals marked. Align the correct terminals and
insert the battery into slot ‘A; in figure 4. Note: the battery pack is designed so that it will only enter the charger unit the correct way.
When placed in the charger, a very slight downward pressure will seat the pack firmly into the power terminals.
The Green LED will remain on continuously indicating that the battery is on a rapid charge
3.1.6. CHARGING COMPLETE, once complete the Green LED will blink rapidly and an alarm (“Bi..Bi..”) sound will be emitted. This means
the battery is fully re-charged and has switched to a “trickle” charge.
3.1.7. TEMPERATURE FAULT, If the Red LED light comes on and remains on when the battery is inserted, and the Green LED blinks
rapidly, the alarm will also sound, this indicates a WARNING that the battery is either too hot or cold, or, that the charger itself is too
hot. To remedy, remove the battery pack and switch off the charger allowing both to stand in order to gain a temperature between
5-40ºC. Then try again. Note: battery may be too hot immediately after use allow battery to cool.
3.1.8. BATTERY DEFECTIVE if you insert battery and the Green LED continues to blink at the slower rate, this indicates the battery is
defective or that the charging contacts are dirty. Action: Switch off the mains power, clean battery and charger terminals.
If this does not remedy the problem it means the battery is defective and you should seek advice from an authorised agent. In the
case of battery defect the Red LED will not light up.
p
p
F (5
C) or above 104
F (40
O
O
O
O
Fig.1
1.
Keyless chuck
2.
Torque Adjuster
3.
Torque & Hammer selection
4.
Two speed switch
5.
Lock, reverse and forward switch
6.
On/Off variable speed switch
7.
12V Battery pack
8.
Battery release button (one each side)
Yellow & Green -
earth wire
Blue -
neutral
wire
FUSE RATING
THE PLUG FITTED TO PRODUCT
MUST BE EQUIPPED WITH A
3 Amp FUSE
C)
fig. 1
fig. 2
CP99722VHK - 0016 - (1) - 010899
Brown - live
wire
Cable clamp
Advertisement
