MEDION P85713 - Remote Control Manual

Declaration of conformity

Medion AG hereby declares that the product conforms to the following European requirements:

• RE Directive 2014/53/EU
• Ecodesign Directive 2009/125/EC
• RoHS Directive 2011/65/EU

Full declarations of conformity are available at www.medion.com/conformity.

Controls and functions

Status LED

The LED light flashes during the pairing process and thus signals that the installation is possible in combination with the app. The LED is not lit during normal operation.

Pair button

The pair button is used to activate pairing mode. The device sends a signal that is registered by the app and which enables the device to be integrated into the app. After the device has been successfully integrated into the app, this button serves as a reset button. If the reset button is unintentionally pressed, the PIN code can be re-entered and the device will be available again without the need for any further action.

The components are also coupled with the central alarm unit. In order to completely remove components, they need to be removed from the app via the device manager.

Arm

The alarm system can be armed via the button. It is not necessary to enter a PIN code. If a delay has been set, a countdown will appear on the display. In this case, the alarm system will only arm those sensors for which there is an alarm delay after the countdown has expired.

NOTICE!
The alarm cannot be armed if a door/window contact is open, a component has a flat battery or the sabotage contact on the outdoor siren or the central alarm unit has already been triggered. A warning message is issued in this case. Please ensure that all security issues have been resolved so that the alarm system can be used properly again.

Disarm

Disarm the alarm system by clicking on the button on your remote control.

Home mode

If the alarm system has been armed and you switch it to home mode , the system will focus on those components that should remain armed when you are physically present in the home. All of the components registered to the home zone are disarmed.

The normal and 24 hour zones remain armed.

SOS

Pressing the SOS button on the central alarm unit will trigger an alarm. If

the alarm is triggered, the previously configured steps in the event of an emergency are carried out.

Registering the remote control

Ensure that the component is located within the reception range of the central alarm unit. If the reception is not sufficient for the relevant component, change the position of the central alarm unit or, if required, add a second receiver to increase the range of the network.

• Tap on Settings in the Smart Home app.

Setting up/configuring components

• Select add Central unit/ Device .
• Under New device, select the desired component

Remote control

• Tap on Set up.
• Follow the further instruc-tions given by the Smart Home app and enter the device PIN when requested.

You can find the relevant device PIN on the device housing. Firstly read off the PIN code, then mount the device and finally set it up. The PIN code may be concealed after mounting and will thus no longer be legible.

Changing the battery

A 3 V button cell battery, type CR2032, is already inserted in the radio remote control on delivery.

If this battery is flat, replace it with a new button cell battery of the same type.

• Open the cover on the remote control using a coin.
• Insert the battery into the fixture provided for this purpose according to the correct polarity.
• If the battery is flat, replace it with a new battery of the same type.
• Remove the flat battery and insert the new battery in accordance with the polarity shown in the battery compartment (see diagram).
• Replace the battery compartment cover and turn it using a coin until it is firmly closed.

Disposal

Packaging
Your device is packaged to protect it from transportation damage. Packaging is raw material and can be reused or added to the recycling system.

Device
Do not dispose of the device in the household rubbish at the end of its service life. Take it to a local collection point for used devices in order to comply with environmental regulations. Contact your local authority to find out where your nearest collection point is located.

Batteries
Batteries must be properly disposed of. Retailers who stock batteries and local authority collection points have appropriate disposal containers for this purpose. You can contact your local waste disposal company or municipal authorities for further information.

Technical data

Weight	approx. 20 g (including batteries)
Power supply	3 V button cell type CR2032
Operating temperature	0°C - 40°C
Humidity during operation	5% - 65%
Dimensions	68 x 37 x 13 mm

Subject to technical changes.

Legal notice

Copyright © 2017

Last revised: 11.09.2017

All rights reserved.

These operating instructions are protected by copyright.

Mechanical, electronic and any other forms of reproduction are prohibited without the written permission of the manufacturer.

Copyright is owned by the company:
Medion AG
Am Zehnthof 77
45307 Essen
Germany