Summary of Contents for Kontron 2-DH47-0010
- Page 1 » User Guide « CC300 Operator Panel Model 2-DH47-0010 User Guide (Version 1.1) P/N: XXXX-XXXX...
- Page 3 In cases of doubt, please contact Kontron. This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the express written permission of Kontron.
- Page 4 ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS"). You understand and agree that your use of Kontron devices as a component in High Risk Applications is entirely at your risk. To minimize the risks associated with your products and applications, you should provide adequate design and operating safeguards.
-
Page 5: Table Of Contents
1. Table of Contents CC300 Operator Panel – User Guide 1. Table of Contents 1. Table of Contents ..........................5 1.1. Table of Figures ............................7 2. Introduction ............................9 2.1. Symbols used in this User Guide ....................... 10 3. Important Instructions ........................11 3.1. - Page 6 1. Table of Contents CC300 Operator Panel – User Guide 7.5.1. Opening the CC300 Operator Panel ....................34 7.5.2. Closing the CC300 Operator Panel ..................... 37 8. Cabinet Installation .......................... 38 9. Maintenance and Prevention ......................43 9.1. Replacing the Lithium Battery ........................43 9.2.
-
Page 7: Table Of Figures
1. Table of Contents CC300 Operator Panel – User Guide 1.1. Table of Figures Fig. 1: CC300 Operator Panel - Nameplate ..................... 17 Fig. 2: Bottom view ............................21 Fig. 3: Right view ............................. 21 Fig. 4: Front view ............................. 21 Fig. - Page 8 1. Table of Contents CC300 Operator Panel – User Guide Fig. 38: Unscrew the cap holder of the rotary/push button ................43 Fig. 39: Rotary/push button and CMOS battery, pulled out of the housing ........... 44 Fig. 40: Removing the rotary/push button (shown with battery removed) ........... 44 Fig.
-
Page 9: Introduction
Kontron Europe GmbH does not accept any liability for any printing errors or other inaccuracies in the manual unless it can be proven that Kontron Europe GmbH is aware of such errors or inaccuracies or that Kontron Europe GmbH is unaware of these as a result of gross negligence and Kontron Europe GmbH has failed to eliminate these errors or inaccuracies for this reason. -
Page 10: Symbols Used In This User Guide
2. Introduction CC300 Operator Panel – User Guide 2.1. Symbols used in this User Guide Symbol Meaning This symbol indicates the danger of injury to the user or the risk of damage to the product if the corresponding warning notices are not observed. This symbol indicates that the product or parts thereof may be damaged if the corresponding warning notices are not observed. -
Page 11: Important Instructions
3.2. Exclusion of Accident Liability Obligation Kontron Europe GmbH shall be exempted from the statutory accident liability obligation if the user fails to observe the included document: “General Safety Instructions for IT Equipment” the hints in this manual or eventually the warning sign labels on the device. -
Page 12: General Safety Instructions For
Observe the warnings and instructions on the device and in the manual. The CC300 Operator Panel has been built and tested by Kontron Europe in accordance to UL 61010-1 - Edition 3 - Revision Date 2019/07/19 and left the company in a perfectly safe condition. - Page 13 4. General Safety Instructions CC300 Operator Panel – User Guide It must be assumed that safe operation is no longer possible, • if the device has visible damage or • if the device no longer functions. In these cases the device must be shut down and secured against unintentional operation. Version 1.1...
-
Page 14: Electrostatic Discharge (Esd)
4. General Safety Instructions CC300 Operator Panel – User Guide 4.1. Electrostatic Discharge (ESD) A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-circuitry. Therefore proper packaging and grounding techniques are necessary precautions to prevent damage. Always take the following precautions: 1. -
Page 15: Instructions For The Lithium Battery
4. General Safety Instructions CC300 Operator Panel – User Guide 4.2. Instructions for the Lithium Battery The installed mainboard is equipped with a lithium battery. For the replacing of this battery please observe the instructions described in the “Replacing the Lithium Battery”... -
Page 16: Electromagnetic Compatibility
5. Electromagnetic Compatibility CC300 Operator Panel – User Guide 5. Electromagnetic Compatibility 5.1. Electromagnetic Compatibility (EU) This product is intended only for use in industrial areas. The most recent version of the EMC guidelines (EMC Directive 2004/108/EC) and/or the German EMC laws apply. If the user modifies and/or adds to the equipment (e.g. -
Page 17: Nameplate Of The Cc300 Operator Panel
5. Electromagnetic Compatibility CC300 Operator Panel – User Guide Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. -
Page 18: Scope Of Delivery
6. Scope of Delivery CC300 Operator Panel – User Guide 6. Scope of Delivery CC300 Operator Panel Scope of Delivery: DP cable Optional Parts: Blind panel Add-on panel Expansion panel Expansion panel 2F Version 1.1... -
Page 19: Product Description
7. Product Description CC300 Operator Panel – User Guide 7. Product Description The CC300 operator panel is a Human Machine Interface (HMI) system designed for demanding industrial applications. As a workstation system with integrated touch screen display it is designed for installation in an instrument panel or other cabinets. - Page 20 7. Product Description CC300 Operator Panel – User Guide The CC300 operator panel complies with IP54 protection class (IP54 not evaluated by UL). The CC300 operator panel is a fanless system. The cooling of the unit is performed by the surface and the cooling fins of the aluminum cover on the rear side of the chassis.
Need help?
Do you have a question about the 2-DH47-0010 and is the answer not in the manual?
Questions and answers