Table of Contents
Advertisement
Quick Links
NC369 Paging Transmitter
Installation Instructions
OVERVIEW
TekTone
's digital paging system can be used to transmit
®
text and numeric messages directly to individual pocket
pagers, or to entire groups of pagers. The NC369 Paging
Transmitter includes both an RJ45 Ethernet port and an RJ45
RS232 serial port to accommodate system programming and
Ethernet or serial input from TekTone
Both ports can be used simultaneously and may be set to
different protocols, allowing greater flexibility.
IMPORTANT SAFETY INFORMATION
TekTone
®
products are designed to operate safely when
installed and used according to general safety practices.
The following requirements should be observed at all times.
• Do not subject this equipment to mechanical shock,
excessive humidity or moisture, extremes of temperature,
or corrosive liquids.
• Do not operate this equipment with the antenna discon-
nected. Doing so may severely damage the transmitter.
• This equipment is designed for indoor use only, unless
expressly stated otherwise, and must not be used in
classified Hazardous Areas, including areas containing
explosive or flammable vapors, unless express authoriza-
tion has been given in writing by the manufacturer.
• Do not obstruct any slots or openings in the product.
These are provided for ventilation to ensure reliable
operation of the product and protect it from overheating.
• Only use a damp cloth for cleaning (not liquid or aerosol
based cleaners), and ensure that any power is removed
from the unit prior to beginning the cleaning operation.
• Removal of covers from the equipment must only be
undertaken by authorized service personnel.
LIABILITY
TekTone
does not accept any liability for any damage or
®
injury howsoever resulting from misuse of this equipment. It
is the responsibility of the user to ensure that the equipment
is operated in the manner for which it was intended and that
it is the correct item of equipment for the required task.
ALPHA COMMUNICATIONS
Toll-Free Technical Line: 1-800-666-4800 • Phone: (631) 777-5500 • Fax: (631) 777-5599
Website: www.Alphacommunications.com • Email: info@alphacommunications.com
nurse call systems.
®
• 42 Central Drive • Farmingdale, NY 11735-1202
®
EQUIPMENT APPLICATIONS
It is the user
s responsibility to determine the suitability of
'
this system for any given application. TekTone
provide specific advice, since each application requires
independent evaluation. TekTone
and application of the frequencies issued by the FCC. Some
licensed equipment may have greater protection than other
equipment operated on a FCC License Exempt basis.
EQUIPMENT TESTING
Conduct range tests at least once a week; more often when
critical criteria apply. This involves testing the unit past the
limit of its required working range, so as to ensure a measure
of safety. TekTone
suggests keeping a log of test dates and
®
the information gathered, along with battery change data
and service records. Required test frequency varies between
applications. If a pager has been dropped or is worn by
someone involved in an accident, test the unit again before
reuse. The physical range tests are essential, and any
construction work or movement of plant or equipment could
alter the signaling capability of the unit.
SERVICE
If your NC369 paging transmitter requires service, return it to
TekTone
at the address listed below. Prior to returning the
®
equipment, you must call TekTone
327-8466 and obtain a return authorization number (RMA
number). No returns will be accepted without an RMA number.
WARNING!
Alteration or modification of any part of this equipment,
without the prior written consent of the manufacturer,
will invalidate all manufacturer Approvals and
Warranties. No adjustments can be undertaken except
by a qualified and licensed person as defined by the
FCC Rules and Regulations. Operation of altered
equipment can result in fines, imprisonment, and/or
confiscation of such equipment.
IL888
Section E
Rev. 6 - 03/2010
cannot
®
®
has no control of the use
s Sales Department at (800)
®'
Advertisement
Table of Contents
Summary of Contents for Alpha Communications TekTone NC369
- Page 1 FCC Rules and Regulations. Operation of altered equipment can result in fines, imprisonment, and/or confiscation of such equipment. ALPHA COMMUNICATIONS • 42 Central Drive • Farmingdale, NY 11735-1202 ® Toll-Free Technical Line: 1-800-666-4800 • Phone: (631) 777-5500 • Fax: (631) 777-5599...
-
Page 2: Unpack The Equipment
UNPACK THE EQUIPMENT INSTALL THE ANTENNA Carefully unwrap and inventory the pager transmitter and all An antenna capable of handling 5 watts must be connected components as shown below. If anything is missing, notify to the BNC connector on the rear panel. The unit comes with TekTone immediately. -
Page 3: Software Configuration
transmitter on the second or third floor of a building will 4. Remember that the performance of the system will be usually boost overall range. However, horizontal range is affected by the type of material the unit is mounted on and not always required so much as propagation through a multi- by its surroundings. - Page 4 SET UP THE PC–NC369 NETWORK NC369 CONFIG TOOL SETTINGS As shipped, the NC369 Pager Transmitter will not work with Using the Config Tool: your TekTone ® nurse call or wireless emergency system— • Clicking on one of the menu buttons on the left first brings you must configure it.
- Page 5 Network Settings—Normally these settings will not need to Transmitter Settings—After all changes have been be changed; use the default settings. If changes are made to made to this menu page, click on the button. SAVE this menu page, check the ? box and then click on REBOOT button.
- Page 6 Protocol—After all changes have been made to this Max Msg Count—The maximum number of messages menu page, check the ? box and then click on that can be sent by a protocol in a single session/ REBOOT button. connection. A value of “0” means no maximum limit SAVE (default 0).
- Page 7 Pocsag—After all changes have been made to this IP Access List—This is the list of IP addresses that are menu page, click on the button. allowed to access the NC369 Paging Transmitter. Do not SAVE make changes to this list. Survey—This button is used to test a site by sending messages periodically.
-
Page 8: Site Survey
SITE SURVEY CONNECT THE SYSTEM Click on the button in the NC369 Config Tool to Use the supplied black cable (serial DB9 to RJ45) to connect SURVEY access the Site Survey screen. the NC369 Pager Transmitter to your TekTone ® nurse call system, wireless nurse call system, or voltage interface.