Download
Share
Print this page
Hix R2R Owner's Manual
  1. Manuals
  2. Brands
  3. Hix Manuals
  4. Power Tool
  5. R2R
  6. Owner's manual

Hix R2R Owner's Manual

Reel to reel care label heat press
Hide thumbs Also See for R2R:

Advertisement

Quick Links

Download this manual
Reel to Reel Care Label Heat Press
OWNER'S MANUAL
For Customer Service, Call 1-800-835-0606
CONTENTS
Receiving
BEFORE warranty repair you MUST get Prior Authorization:
R2R
or Visit www.hixcorp.com
Call 1-800-835-0606
R2R shown
70594 RV A_100610
2
3-6
7
7-9
10
11
12

Advertisement

loading
Need help?

Need help?

Do you have a question about the R2R and is the answer not in the manual?

Questions and answers

Related Manuals for Hix R2R

Summary of Contents for Hix R2R

  • Page 1: Table Of Contents

    Reel to Reel Care Label Heat Press OWNER’S MANUAL R2R shown For Customer Service, Call 1-800-835-0606 or Visit www.hixcorp.com CONTENTS Receiving Installation Operation Sensor Setting Transfer Application Trouble Shooting Warranty BEFORE warranty repair you MUST get Prior Authorization: Call 1-800-835-0606...
  • Page 2 Damage to the machine’s internal air operated components can occur that will not be covered under warranty. Combination air filter/water traps are available at any major hardware store or may be purchased directly from HIX (part #71145).

  • Page 3: Installation

    INSTALLATION 3. Set pressure Turn Knob below air gauge right to increase pressure. Left to decrease pressure. NOTE: air pressure will not decrease until machine cycles. Set starting pressure to 40-50 PSI. 4. Push Emergency stop button. 5. Make sure auto/manual button is in the “out” manual position. (Press and release to change button position) 6.
  • Page 4 INSTALLATION 8. Push Yellow power button. Time/Temp display will light. 9. Set your desired time and temp. a. To change or set the temperature, press the menu button on the digital control. The light next to “TEMP” will light. Press the up s, or down t, button to your desired setting.
  • Page 5 INSTALLATION Continue web underneath heat platen and underneath right elbow web guide. Feed over top guide rod and through slot in drive roller mount. Top Guide Rod Right Elbow Web Guide Drive Roller Mount For effective web tracking labels should be fed between drive roller and pinch roller then back over top of pinch roller.
  • Page 6 INSTALLATION Simply place lead edge of label web between four fingers of take up real and let hang free. 14. Take up slack by pressing and releasing Jog button on left side of control box. 15. Set sensor position and sensitivity. (See sensor section page 8) Index Mark 16.

  • Page 7: Operation

    OPERATION 1. Visually check and confirm label is in centered position. (Note: If it is NOT repeat sensor setting Page 8) 2. Position Garment into desired position 3. Place finger in each optical control switch, heat head will come down and then rise after set time, take up roll will automatically index to next label.
  • Page 8 SENSOR SETTING 2. Reposition guides on guide rod to maintain front to rear centering of label. Do not adjust left to right position at this time. Guides on guide rods 3. Depress manual/auto button to the “out” position or manual mode 4.
  • Page 9 SENSOR SETTING 9. Now adjust position of sensor head such that the light beam is just above the Index mark (approx. 3mm) and tighten. NOTE: When sensing an index mark on a reflective (shiny) material, mount the sensor at approximately 15° off perpendicular to the material’s surface to minimize strong direct reflections and allow the sensor to discern the relatively small optical contrast offered by differences in colors.

  • Page 10: Transfer Application

    TRANSFER APPLICATION When you fail to make a successful transfer you can wonder, “Is it the machine’s fault, or the transfer, wrong settings or what”? FIRST, THE BASICS: 1. Be sure to set the heat transfer machine to the transfer manufacturer’s recommended Temperature, Time and Pressure settings.

  • Page 11: Troubleshooting

    TROUBLESHOOTING Symptom Cause Solution 1. Machine does not Press set to Manual De-Press Manual/ index properly. Auto button Sensor not set prop- First make sure label erly is aligned properly. Re-Teach sensor. See “Sensor Section” pg 8. 2. Labels do not trans- Not enough heat, time Please refer to fer properly.

  • Page 12: Warranty

    In the event of a defect, HIX, at its option, will repair, replace or substitute the defective item at no cost during this period subject to the limitations of insurance and shipping costs stated below.