Page 1
Models included: Models included: • GEO • GEO/GEO 1.3 • EDGE • EDGE/EDGE 1.3 • BCR/BCR 1.3 • AREA/AREA 1.3 • OMNI/OMNI 1.3 Printed in USA Printed in USA 12/04 02/06 P/N 118000 rev. D P/N 118000 rev. A...
Page 2
This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de- energized sensor output condition. Consult your current Banner Safety Products catalog for safety products which meet OSHA, ANSI and IEC standards for personnel protection.
Introducing PresencePLUS P4 The PresencePLUS P4 (or the Sensor) is an easy-to-use vision sensor with advanced visual inspection capabilities. With minimal knowledge of vision, a user can quickly set up the Sensor to run an inspection that tests all products and accurately rejects bad products on a production line.
Caution: If the light is powered by the Sensor, the Sensor power source must be 24V dc. b. Caution: This connection is for Banner lights only! . If an NTSC monitor is used, connect it to the Sensor via a BNC-to-BNC cable to the NTSC Video connector.
Page 5
(see pin assignments below). 1-pin Discrete I/O Power/Ground RS-3 Serial (see pin assignments below) Ethernet (RJ-) Light Connector (3-pin Pico Style) (Banner lights only) 1 = Brown 24V NTSC Video 2 = n/a (BNC) 3 = Blue (ground) 4 = Strobe...
Page 6
Write down the existing address of your PC before changing it: _ _ _ • _ _ _ • _ _ _ • _ _ _ To change the IP address of your PC, do the following: The following screen captures are from Windows XP. For earlier Windows versions, see Banner’s Supplemental Information at http://info.bannersalesforce.com/xpedio/groups/public/documents/trainingjobaid/vr_01_00_e.pdf.pdf...
Insert the Installation CD. b. Click Install PresencePLUS PC Software. step step Starting the PresencePLUS P4 1. Power up the hardware and verify that the Power/Error light turns Green = Power Green. This may take up to 20...
6 step 6 Software Setup Use the Main Menu toolbar to navigate the PresencePLUS P4 options. Proceeding from left to right, the buttons in the Menu toolbar step through the process of creating an inspection file. Inspection Work Flow Set up the Sensor, lens, and lighting, to acquire a reference image.
Vision tool and one Test tool. • Save a backup copy of your inspection to the host PC. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 P/N 118000 rev. D...
See the Tool User’s Manual in the Help menu Failing for complete Tool information. To begin inspecting, click the Start button in the Run screen. Banner Engineering Corp. Minneapolis, MN U.S.A. • www.bannerengineering.com • Tel: 763.544.3164 P/N 118000 rev. D...
Installation Help versions. The Lens Selection Help information will be helpful if you Lighting Help call Banner for Error Codes support. About (GUI Software version, Sensor Firmware version, Hardware version, Sensor’s physical address) Banner Engineering Corp. Minneapolis, MN U.S.A.
Do not use any other chemicals for cleaning. Updating PresencePLUS Software The current version of PresencePLUS software is available for download from the Banner website: www.bannerengineering.com Click on Literature/Resources. Click on Software and Electronic Data Sheets.
• Errors when saving inspections to the Sensor. * Support is available from your local Banner representative or a Banner Applications Engineer. Call, e-mail, fax, or write for support. Applications Engineers are available from 8:00 A.M. to 5:00 P.M. Central Time, Monday through Friday, excluding holidays.