After Operation; Cleaning And Maintenance - PITSOS GMX1264M User Manual

●
The mixers are intended to work the rubbed dough,
yeast dough, cheeses cakes, imbirbread cakes, etc.
●
The whisks and mixers shall be assembled in sockets on
the bottom of the robot.
1 Press until you feel the refusal – when the clamps get
fastened.
When assembled improperly, the parts fall
apart during operation.
2 Insert the mixer or whisk with toothed bar into the socket
marked with a star.
The reverse assembling of the mixers can
cause lifting up the dough (taking the dough
out of bowl).
The level of products inside the bowl should
not exceed the hight of mixers or whisks
working part (L).
1 cm L
OPERATION WITH LIQUIDISING DISC
●
Liquidizing disc is used for liquidizing boiled fruit and
vegetables such as: carrots, potatoes, tomatoes, apples
through the sieve. It partly replaces the function of the
mixing adapter.
1 Insert the liquidizing disc on the whisk with toothed bar
from the bottom side.
2 Insert the whisk into the socket marked with a star.
OPERATION WITH STAND INCLUDING
TURNABLE BOWL
The stand with assembled motor part makes the operation
with whisks or mixers easy, as the user does not have to hold
the device.
The housing with the bowl is equipped with a self-
gathering spatula, which is an innovative solution.
It helps to effectively blend the products, prevents the dough
from gathering on the edges of the bowl and shortens the
preparation time.
The stand head driver automatically makes the head move
pendulum-like and simultaneously turns the bowl with the
mixed product.
You can use the stand with specially prepared whisks and
mixers only. The device equipped with stand includes also
one mixer and one whisk with toothed bar.
1 Insert the mixers or whisks into the motor casing
(as described above).
2 Assemble the drive in the stand head after moving the
cover (like during assembling the adapter) the following way:
Insert the drive fasteners (which are located near the holes
for whisks assembling) under the stand head fastener.
481-001PI_v01
3 Turn the control clamp to the limit in such a way that the
hand is positioned vertically.
4 Press the fastener button and simultaneously deflect the
stand head with the motor part back.
5 Before putting the ingredients into the steel bowl, attach
the toothed wheel plastic rim to the bowl until it sits in the
recess.
6 Then twist it in the direction marked on the rim until it
stops.
7 Place the bowl on the 3 lips of the stand and put it on the
stand base.
8 Attach the bowl scraper attachment and put ingredients
into the bowl.
9 Place the stand head with the motor part in horizontal
position (you will hear the clicking sound of fastener blocking
clamps).
10 Start-up the mixer with the switch lever and it will make
the bowl turn and the head with drive move pendulum-like.
1 cm L
D

After operation

●
Depending on assembled equipment:
1 Push the whisks or mixers out with a pushing button.
F
2 Disassemble the liquidizing disc from the whisk.
3 Deflect the stand head with the motor part back. Turn
the clamp knob in counter clockwise direction as much as
possible and put the motor out of the head fasteners.
●

Cleaning and maintenance

Remember to unplug before clearing and maintenance.
●
●
●
●
●
Never block or stop the oscillatory movement
during operation. It may cause damage to the
housing.
Before emptying the metal bowl, take away
toothed wheel. Removing toothed wheel
facilitates emptying and cleaning of the
product.
Switch the mixer off and unplug it.
Wind the cord onto the motor.
Clean the whisks and mixers with warm water with
cleaning agents.
Clean the cogged rim of rotational bowl with dishes
cleaning brush.
Before cleaning the steel bowl disassemble the toothed
wheel rim proceeding in reverse to the assembly
instruction (Fig. ).
H
Dry the mixer equipment after cleaning and store in dry
place.
Clean the motor or stand casing with dump cloth and
then dry it.
E
11