Related Manuals for Easy PA Series
Summary of Contents for Easy PA Series
- Page 1 PA PUBLIC ANNOUNCEMENT AMPLIFIER User’s Manual Contact Information support@singeasy.com https://singeasy.com...
- Page 2 IMPORTANT SAFETY INFORMATION WARNING FOR YOUR PROTECTION READ THE FOLLOWING: KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS The apparatus shall not be exposed to dripping or splashing liquid and no object filled with liquid, such as vases, shall be placed on the apparatus.
- Page 3 IMPORTANT SAFETY INFORMATION SAFETY INSTRUCTIONS NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD. WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION. The cores in the mains lead are coloured in accordance with the following code: GREEN and YELLOW - Earth BLUE - Neutral BROWN –...
-
Page 4: Table Of Contents
Table of Contents Table of Contents Section 1 - Welcome 1.1 Welcome ..........................5 1.2 Contact Info ..........................5 Section 2 - Features 2.1 Front Panel Features ....................... 6 2.2 Back Panel Features ....................... 7 2.3 Protection Features ......................... 8 Section 3 - Setup 3.1 Get Started .......................... -
Page 5: Section 1 - Welcome
Welcome 1.1 Welcome Congratulations on your purchase of the Sing Easy PA Series. The PA Series is a a 2U mixer public announcement amplifier gives your entertainment or PA system a boost! Provides convenient 3 microphone inputs, 2 AUX inputs and speaker control with 100V, 70V, 16 ohm, 8 ohm, and 4 ohm speaker outputs, supporting speakers with 4 to 16 ohm impedance. -
Page 6: Front Panel Features
Section 2 Features 2.1 Front Panel Features Power Switch & Power LED Amplifier is on when the switch is in the UP position. Master Level Control Rotate to adjust the master volume. ... -
Page 7: Back Panel Features
Section 2 Features 2.4 Back Panel Features Microphone Override Priority Level Adjustment Knob When MIC 1 is activated, MIC 2, MIC 3, AUX1 and AUX2 signals will be attenuated by 0 to ... -
Page 8: Protection Features
The cause of your amplifier’s thermal protection state should be determined and corrected as soon as possible. Without correction, the Thermal Protection circuit will typically reactivate. 3. Fuse Protection The high-voltage power supplies of your Sing Easy amplifier are protected by a fuse. -
Page 9: Section 3 - Setup
3.1 Get Started Choose Output Wire and Connectors Sing Easy recommends using professionally wired, high quality, two-conductor, heavy gauge speaker wire and connectors. You may connect the bare wire from your speaker to the output terminal to prevent the possibility of short-circuits, wrap or otherwise insulate exposed loudspeaker cable connectors. -
Page 10: Stereo Mode
1. Connect the speakers, microphone and music player to the PA Series, 2. Power on all audio output devices then power on the PA Series. 3. While playing back audio, slowly increase the volume of the PA Series to the desired listening level. -
Page 11: Connect To Ac Mains
Connect the PA Series to the AC mains power source (power outlet) with the supplied AC power cordset. First, connect the IEC end of the cordset to the IEC connector on the PA Series; then, plug the other end of the cordset to the AC mains. -
Page 12: Lcd Screen
8. Do not operate the amplifier with less than the rated load impedance. Due to the amplifier’s output protection, such a configuration may result in premature clipping and speaker damage. Remember: Sing Easy is not liable for damage that results from overdriving other system components. - Page 13 Section 4 F.A.Q. 4.1 F.A.Q. Before submitting the device for repair, please check the below frequently asked questions. FAULT REASON SOLUTION Connect power plug The power plug is not plugged correctly and ensure good in properly contact No sound output and the display does not light up Unplug power...
-
Page 14: Section 4 - F.a.q. 4.1 F.a.q
Section 5 Appendix 5.1 Specifications PA350 PA500 PA650 Rated Output 350W 500W 650W Speaker Outputs 4 to 16 ohm, 70V and 100V Frequency Response 60 Hz - 15k Hz (± 3 dB) Total Harmonic Distortion <0.5% at 1kHz, 1/3 of the rated output power Signal to Noise Ratio Line: 85dB / MIC: >72 dB Mic Inputs...