Related Manuals for Neilsen CT5643
Summary of Contents for Neilsen CT5643
- Page 1 220L SAND BLASTING CABINET WITH BLASTING GUN CT5643 ORIGINAI INSTRUCTION Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM SAVE THESE INSTRUCTIONS FOR REFERENCE...
-
Page 3: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: 220L SAND BLASTING CABINET WITH BLASTING GUN Model: CT5643 Applicable EC Directives: EC Machinery Directive 2006/42/EC EC EMC Directive 2014/30/EU... -
Page 4: Specifications
1. SPECIFICATIONS Air compressor delivery: 60-120PSI @ 15-25CFM Maximum operation pressure: 110 PSI Nozzle size: 4/5/6/7mm Working space: 84 x 55 x 38cm Overall Dimensions: 138 x 87 x 63cm Noise pressure 70dB(A) 12V FLUORESCENT WORK LIGHT WITH 110 V/ 230VAC 50HZ input 12V 800mA output 2. - Page 5 operating the cabinet. Use mask when filling hopper. During operation, do not expose the hands or skin directly in the line of the blast nozzle. 7). Keep the unit lid closed and secured when in use. 8). WARNING! Ensure correct air pressure is maintained and not exceeded. 9).
- Page 6 The dust can be created when you sweep, blast, cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. Fire or Explosion Hazard! DO NOT USE a sand blaster around combustible or flammable liquids, dusts, gases, oily rags, or other materials that can explode or burn quickly.
-
Page 7: Technical Description
3. TECHNICAL DESCRIPTION 4. UNPACKING AND CHECKING Carefully remove the product from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the seller and do not attempt to use the product. -
Page 8: Air Supply
5. AIR SUPPLY a). You will require an air pressure of 60-120psi, and an air volume of at least 15cfm to operate the unit efficiently. b). WARNING! Ensure air supply is clean, dry and does not exceed 125psi.Too high an air pressure and/or unclean or damp air will shorten the product life due to excessive wear and may be dangerous, causing possible damage and/or personal injury. -
Page 9: Assembly And Operation
6. ASSEMBLY & OPERATION LEG INSTALLATION 1. Place cabinet on its back on a table or Bench. 2. Remove M6 x 12 bolts nuts lock washer & washers from bolt packet. 3. insert M6 x 12 bolt through leg & into cabinet. - Page 10 CABINET LEG TRIM MOULDING Enclosed are four trim Mouldings for bottom of cabinet legs. They may be pushed in place, without tools. AIR REQUIREMENTS: For best results, we recommend a good 5 HP air compressor. A small nozzle/air jet combo is use with a 3 HP air compressor. HOW IT WORKS Your shop air hose enters front opening of cabinet and is connected to the air inlet of power gun.
-
Page 11: Maintenance
funnel area. Do not over fill (1/2 full below work area screen is best). NOTE: use a fine grade of abrasive to prevent clogging. We recommend straining through a double layer of ordinary window screen. If it passes through the screen, it will pass through the nozzle. YOU ARE READY TO START BLASTING. -
Page 12: Troubleshooting Chart
If visibility is reduced, replace the protective cover. 10. Check that the gloves are in good condition. If damaged replace immediately. 8. TROUBLESHOOTING CHART Symptom (s) Possible Causes(s) Corrective Action(s) Excessive dust in the 1.Exhaust vent or air flow block. 1. - Page 13 10. SYMBOLS The following symbols are used in this manual and/or on the machine: WARNING – To Denotes risk of personal reduce the risk of injury or damage to the injury, user must read tool instruction manual” In accordance with Mandatory use of eye essential safety protection...
-
Page 14: Exploded View
11. EXPLODED VIEW... - Page 16 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...