Advertisement
Quick Links
Advertisement
Summary of Contents for Daniels 844.BLU.PLOW
- Page 1 3-IN-1 PLOW Operator’s Manual 844.BLU.PLOW (844.258.7569) www.danielsplows.com...
- Page 2 Prior to completing the installation process, make sure your loader meets all the requirements needed to operate the Daniels 3in1 Plow. Your loader must also be equipped with an auxiliary hydraulic circuit (i.e., 3rd Caution: saws.
- Page 3 PLOW INSTALLATION 1. Connect the Daniels 3in1 Plow to the loader, making sure the plow is securely locked in place IMPORTANT! Check to be sure the 8” X 8” square tube (Throat Weldment) is parallel to the pavement, as shown (Page 13, Diagram 2). When...
- Page 4 PLOW INSTALLATION 3. Electric switch installation harness has been pre assembled prior to shipping. a boot along the steering column, or through a hole Prior to installing the electric wire harness and switch be drilled, select an area with no obstruction, on either by connecting the electrical connector plug to the edges.
- Page 5 PLOW INSTALLATION 4. Plow function cycle check Set the parking brake and start the machine. Raise WARNING! During ALL operations of the plow weldment level with the ground. during installation or plow use it is the With the electrical switch in the middle “neutral” operators responsibility to make sure the entire area around the machine and plow and right until the plow moves smoothly in both...
-
Page 6: Operation
To raise the plow, move the bucket lever to the “roll back” position. This will cause the chains to tighten and the plow to rise. Always transport the Daniels 3in1 Plow with the wings WARNING! Always use the hazard and running lights and stay as... -
Page 7: Maintenance
OPERATION IMPORTANT: position. The plow should only be raised when the blade is in the straight position. The standard swivel Lower the plow in a slow and smooth motion. Dropping the plow may cause the cutting edge bolts to loosen CAUTION! Know the areas you are plowing! Hitting manhole covers or other hidden... - Page 8 The center wear edge, wing wear edges, and all wear items should be checked regularly and replaced REMOVING THE PLOW OFF SEASON STORAGE AND MAINTENANCE It is recommended the Daniels 3in1 Plow be stored indoors. Connect the hydraulic couplers together and exposed cylinder rods to inhibit corrosion. 3-IN-1 PLOW...
- Page 9 3-IN-1 PLOW Parts & Diagrams...
- Page 10 3-IN-1 PLOW Parts & Diagrams...
- Page 11 3-IN-1 PLOW Parts & Diagrams...
- Page 12 3-IN-1 PLOW Parts & Diagrams...
- Page 13 3-IN-1 PLOW Parts & Diagrams...
- Page 14 I N C O RR E C T CO R RE CT C O RR EC T I N C O R R E C T I NCO RRE CT COR R EC T 3-IN-1 PLOW Parts & Diagrams...
- Page 15 Daniels representative, has not been subject to any repair work or replacement parts not authorized in writing by Daniels, and has not been used in any way other than its intended purpose. This warranty does not apply to any “wear parts” such as cutting edges, springs, wear shoes and curb guards.
- Page 16 Daniels Plows, Inc. Warranty Information www.danielsplows.com/warranty please go to to register. Date Purchased: Dealer Name / Address: Model: Serial Number: Company Name: Owner: Address: City: State: Zip: Phone: Mobile: FAX: Email: Was this snowplow assembled and installed by the dealer? YES / NO Was the owner’s manual included with the snowplow?
Need help?
Do you have a question about the 844.BLU.PLOW and is the answer not in the manual?
Questions and answers