Related Manuals for Rocstor SolidRack 8U
Summary of Contents for Rocstor SolidRack 8U
- Page 1 ® SolidRack 8U/12U/22U Wall Mount Adjustable Rack Enclosure 2-Post Open Frame Rack User Manual...
-
Page 2: Table Of Contents
Table of Contents Page Rocstor Legal Disclaimer Important Safety Information Safety Instructions Introduction Component Identi cation Hardware and Accessories 7, 8, 9, 10 Assemble the Rack (22U) 11, 12 Assemble the Rack (12U) Assemble the Rack (8U) Enclosure Installation Warranty... -
Page 3: Rocstor Legal Disclaimer
Copyright, intellectual, and all other proprietary rights in the content of the manual (including but not limited to software, audio, video, text, and photographs) rests with Rocstor or its licensor. All rights in the content are the property of Rocstor and are not granted, licensed, assigned or otherwise passed to the purchaser’... -
Page 4: Important Safety Information
Important Safety Information Please review and read the instructions very carefully in order to understand the speci cation of the equipment. This is essential information before installing, operating, service or maintaining your equipment. These messages or alerts may appear throughout this publication and manual for your purchased equipment. The messages are designed to warn you of possible hazards or to bring to your attention the information that would assist and clari es steps and procedures. -
Page 5: Safety Instructions
Safety Instructions Please follow the essential and important instructions in this manual. The information provides you useful instructions for installation and customization of the rack or equipment. WARNING TIP/ HEAVY EQUIPMENT HAZARD • The content of this packaging is easily tipped. Please be extra careful and use extreme caution when moving or unpacking this cabinet. -
Page 6: Introduction
Introduction SolidRack 8U/12U/22U Wall Mount Adjustable Rack Enclosure - 2-Post Open Frame Rack - Low-Pro le Switch-Depth Heavy Duty Rack - 150 lb (68 kgs) Maximum Load Capacity - 19" Rack Compatible - Cold-rolled Steel CRS - Flat-Pack, Assembly Required -... -
Page 7: Component Identi Cation
Component Identi cation Parts List Long Vertical Mounting Rail Short Vertical Mounting Rail Top/Bottom Panel Frame Left/Right Long Support Beam Left/Right Short Support Beam Mounting Rail Tie Plates Page... -
Page 8: Hardware And Accessories
Hardware and Accessories M5 x10mm Screws Anchors 12-24 Mounting Screws Hex Wrench Zip Ties Page... -
Page 9: Assemble The Rack (22U)
Assemble the Rack (22U Con guration) 1. Insert one end of the Long Vertical Mounting Rails (2 ) into the corner of the Bottom Panel Frame (1) (both panel frames can be used as a top or a bottom) and secure them with 2 of the M5 x 10 mm Hex Head Screws on each side using Hex Wrench. -
Page 10: Assemble The Rack (12U)
Assemble the Rack (22U Con guration) 2. Using one of the Mounting Rail Tie Plates (6) and six of the M5 x 10 mm Hex Head Screws, connect one set of the Short Vertical Mounting Rails (3) to the Long Vertical Mounting Rails (2) using Hex Wrench. Repeat this step for the other set of vertical rails. -
Page 11: Assemble The Rack (8U)
Assemble the Rack (22U Con guration) 3. Insert and connect the Top Panel Frame (1) onto the combined vertical mounting rails with 2 of the M5 x 10 mm Hex Head Screws on each side using Hex Wrench. Page... - Page 12 Assemble the Rack (22U Con guration) 4. Attach Right and Left Long Support Beams (4) to the frame by securing 8 of the M5 x 10 mm Hex Head Screws to the sides of the Top Panel Frame (5) and Vertical Mounting Rails using Hex Wrench. Attach the Right and Left Short Support Beams (5) to the frame by securing 8 of the M5 x 10 mm Hex Head Screws to Vertical Mounting Rails and to the Bottom Panel Frame (1) using Hex Wrench.
- Page 13 Assemble the Rack (12U Con guration) 1. Insert one end of the Long Vertical Mounting Rails (2) into the corner of the Bottom Panel Frame (1) (both panel frames can be used as a top or a bottom) and secure them with 2 of the M5 x 10 mm Hex Head Screws on each side using Hex Wrench.
- Page 14 Assemble the Rack (12U Con guration) 3. Attach the Right and Left Short Support Beams (5) to the frame by securing 8 of the M5 x 10 mm Hex Head Screws to Long Vertical Mounting Rails (2) and to the Bottom Panel Frame (1) using Hex Wrench. Page...
- Page 15 Assemble the Rack (8U Con guration) 1. Insert one end of the Short Vertical Mounting Rails (3) into the corner of the Bottom Panel Frame (1) (both panel frames can be used as a top or a bottom) and secure them with 2 of the M5 x 10 mm Hex Head Screws) on each side using Hex Wrench.
-
Page 16: Enclosure Installation
Enclosure Installation CAUTION CAUTION, This symbol is used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, can result in equipment damage. Please follow instructions carefully. Please follow instructions carefully. NOTICE NOTICE This symbol provides informations and practices not related to physical injury including certain environmental hazards, potential damage or loss of data. -
Page 17: Warranty
In the event Rocstor repairs or provide a replacement of a defective product or part, the warranty does not extend the original warranty period. Rocstor reserves the right to repair or replace any parts under warranty as new or factory re manufactured. -
Page 18: Contact Information
General sales information: sales@Rocstor.com Corporate sales information: corporate_sales@Rocstor.com Educational sales information: academic_sales@Rocstor.com Federal, State & Local government sales information: government_sales@Rocstor.com Resellers/Business Development/OEM Partners All Channel National and International Resellers, VARs, Consultants … contact Rocstor Channel Sales: call: +1 (818) 727-7000 Email: reseller_info@Rocstor.com...
Need help?
Do you have a question about the SolidRack 8U and is the answer not in the manual?
Questions and answers