Advertisement
4.
USING THE TRUCK
4.1.
Before first use.
4.1.1. Before using the truck for the first time purge any air from the hydraulic circuit by pumping the foot pedal 10 to 15 times whilst holding
the release lever (fig 3.A) in.
4.1.2. Test the truck by releasing the lever which will close the hydraulic valve. Pump the foot pedal (fig 2.B) and raise the truck platform to its
highest position and then pull the valve lever (fig 3.A) to lower the platform, (the platform may be slow to descend immediately from its
highest point). If the truck is in full working order it is now ready to use.
4.2.
Using the truck
F
WARNING! Ensure you read, understand and follow the safety instructions. Ensure all Health and Safety, local authority, and general
workshop practice regulations and recommendations are strictly adhered to when lifting or moving heavy loads. The lifting or
movement of heavy loads may be dangerous if not undertaken correctly.
4.2.1. Move the truck to the required loading area and raise the platform to loading height.
4.2.2. Lock the truck wheels with the wheel foot pedal.
4.2.3. Load the truck accordingly.
4.2.4. Lower the truck platform to the lowest position before unlocking the wheels.
F
WARNING! Ensure the load will not foul on anything, and is clear of your hands and the handle when lowering (fig 4).
4.2.5. Unlock the wheels and transport the load to the required destination.
4.2.6. To unload, lock the wheels and raise platform if required, then unload the truck accordingly.
Note: With or without a load, always transport the truck with platform in its lowest position.
When not in use, store the truck with the platform in the lowest position.
4.3
Lowering the handle for storage. Ensure that the platform is at its lowest position. Move the foot pedal down slightly with the heel of
your foot until you are able to press down on the locking lever with the front of your foot (see fig.1A) in order to release the locking
mechanism. As you lower the handle squeeze the release trigger to ensure that the platform sinks to its lowest level in order that the
handle lies flat.
5.
MAINTENANCE
5.1.
When the truck is not in use, the platform must be in the lowest position to minimise ram and piston corrosion.
5.2.
Keep the truck clean and wipe off any oil or grease. Lubricate all moving parts with acid free oil.
DO NOT use truck if believed to have been subjected to abnormal load or shock load. Inspect and if necessary take appropriate action.
5.3.
Periodically check the pump piston and piston rod for signs of corrosion. Clean exposed areas with a clean oiled cloth.
IMPORTANT: Only fully qualified personnel should attempt maintenance or repair of the truck hydraulic system.
The oil cylinder is a sealed unit and must not be accessed. For service contact your authorised dealer.
F
WARNING! Only a good quality hydraulic oil, such as SEALEY HYDRAULIC JACK OIL must be used, DO NOT use brake fluid.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE TRUCK.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK. DO NOT RETURN TRUCK
TO US. Please telephone 01284 757500 to obtain address and ‘phone number of your local agent. If truck is under guarantee please contact your dealer.
De-commissioning the truck: Should the truck become completely unserviceable and require disposal, draw off the oil into an approved
container and dispose of the truck and the oil according to local regulations.
Hydraulic Power Truck
Models HPT300, HPT500.
98/37/EC Machinery Directive (S.I. 1992/3073)
93/68/EEC CE Marking Directive
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof
of which will be required for any claim. INFORMATION: Call 01284 757525 for our catalogue & promotions. Leave your full name, address & postcode.
fig 3
Declaration of Conformity
are in conformity with the following EEC standards and directives
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
%
%
fig 4
We, the sole importer into the UK, declare that the products listed here
The construction file for these products are held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products
01284 757500
01284 703534
9th September 2002
Web address: www.sealey.co.uk
E-mail: sales@sealey.co.uk
HPT300, HPT500 - (2) - 090902
Advertisement
