Summary of Contents for Mei-cha HIRA
- Page 1 QUICKSTART GUIDE H E LL O@M E I - C H A. COM + 1 9 4 9 7 8 8 08 8 2 — L AKE FORE ST, C A @ M E IC H A_O FFIC I AL # M A DE W I T H ME IC HA...
-
Page 2: Read First
READ FIRST THIS MEI-CHA DEVICE IS INTENDED FOR PROFESSIONAL USE ONLY. BEFORE USING THIS DEVICE READ ALL GUIDELINES AND INSTRUCTIONS. Use only cartridges with complete sealed membrane to prevent any fluid backflow. Use barrier or sleeve to protect your device from fluid and contamination. -
Page 3: Important Safety Instructions Read First
Do not allow to be used as a toy. Keep away from children and pets. Keep the device in its protective case and away from dust when not in use. Please contact MEI-CHA or authorized distributor if you have any additional questions. -
Page 4: Troubleshooting
Do not immerse in any liquid. If dropped in liquid, retrieve with WARRANTY caution. Do not allow to be used as a toy. Keep away from children and pets. Please contact MEI-CHA or authorized distributor if you have any additional questions. -
Page 5: Technical Data
CHARGING BATTERY CHARGING TIME 3.5 Hours TROUBLESHOOTING RUNTIME WITH Up to 6 Hours MEI-CHA CARTRIDGES RUNTIME WITH WARRANTY Up to 4 Hours ** TATTOO CARTRIDGES * Optimized for permanent makeup procedures ** Operating duration will decrease while using tattoo cartridges with larger... - Page 6 DEVICE SHELL MATERIAL Grade Aluminum DEVICE WEIGHT 3.9 oz 2 mm * STROKE LENGTH Faulhaber DC Motor MOTOR HIRA DEVICE REPLACEMENT O-RING X2 5400/90 | 6300/105 SPEED RPM/PPS 6900/115 | 7800/130 850mAh Lithium-ion BATTERY PACK BATTERY CHARGING TIME 3.5 Hours...
- Page 7 ASSEMBLY — INSTALLING BATTERY PACK KIT CONTENTS 1. Match the indicators on the device and insert the battery pack. HIRA DEVICE REPLACEMENT O-RING X2 OPTIONAL GRIP FOR STANDARD TATTOO USB TYPE A TO TYPE C 2. Rotate the battery pack clockwise 45° to lock, as illustrated.
- Page 8 ASSEMBLY — INSTALLING BATTERY PACK ASSEMBLY — USING NEEDLE CARTRIDGE 1. Match the indicators on the device and insert the battery pack. Insert needle cartridge to the opening of the grip and rotate clockwise until locked into position. 2. Rotate the battery pack clockwise 45° to lock, as illustrated.
- Page 9 ASSEMBLY — USING NEEDLE CARTRIDGE ASSEMBLY — INSTALLING OPTIONAL TATTOO GRIP Insert needle cartridge to the opening of the grip and rotate 1. Remove the grip by turning it counterclockwise. clockwise until locked into position. 2. Confirm the three o-rings are present on the device, as illustrated.
- Page 10 ASSEMBLY — USING STANDARD TATTOO ASSEMBLY — INSTALLING OPTIONAL CARTRIDGE WITH OPTIONAL GRIP TATTOO GRIP 1. Remove the grip by turning it counterclockwise. 1. Insert tattoo cartridge* into the opening of the grip and rotate clockwise until locked into position. *Use cartridges with sealed membranes to avoid contamination.
- Page 11 OPERATION — ADJUSTING NEEDLE LENGTH ASSEMBLY — USING STANDARD TATTOO CARTRIDGE WITH OPTIONAL GRIP 1. Insert tattoo cartridge* into the opening of the grip and 1. Power on the device with needle cartridge attached. rotate clockwise until locked into position. 2.
- Page 12 OPERATION — ADJUSTING NEEDLE LENGTH OPERATION — POWERING ON/OFF 1. Long press the button on the battery pack for 1.5 seconds to power on/o . SMART MEMORY MODE: the device will 1. Power on the device with needle cartridge attached. memorize the last speed setting used and start with the same setting on the next power up.
- Page 13 OPERATION — POWERING ON/OFF CHARGING 1. Long press the button on the battery pack for 1.5 seconds 1. The LED on battery will blink when remaining battery is to power on/o . SMART MEMORY MODE: the device will below 20%. Detach the battery from device to charge. memorize the last speed setting used and start with the same setting on the next power up.
- Page 14 Your serial number can be found on the main body of the device. If you still have questions about your device after the above steps have been taken, please contact MEI-CHA with your serial number and details of where and when you bought the device.
- Page 15 Use only USB to USB-C Wrong cable cable for charging. Confirm the battery pack MEI-CHA warrants the HIRA device for a period of six (6) months MOTOR IS No power is installed correctly in the starting from the original date of purchase, against defects due to...
-
Page 16: Limitation Of Liability
WARRANTY MEI-CHA warrants the HIRA device for a period of six (6) months starting from the original date of purchase, against defects due to faulty manufacturing or material. If you discover a defect and notify MEI-CHA during the warranty period, MEI-CHA will repair or replace the machine free of charge.
Need help?
Do you have a question about the HIRA and is the answer not in the manual?
Questions and answers