ZALMAN ZM-HPS10BT Series - Bluetooth Stereo Headset Manual

Thank you for choosing the Bluetooth Stereo Headsets. This manual will help you operate the Bluetooth Stereo Headsets, but you should first familiarize yourself with the Bluetooth functionality of your mobile phone or other device before using the Bluetooth Stereo Headsets.

Safety Rules

1. Please follow the rules depicted in this manual closely to ensure your safety.
   Before using this Bluetooth Headsets, we would strongly encourage you to read through this user manual.
2. Do not modify, repair or disassemble this Bluetooth Headsets.
   Doing so may result in fires, electric shocks, complete breakdown of this Bluetooth headsets and etc. all of which are not covered under warranty.
3. Do not use any diluents or volatile liquid to clean the Bluetooth headsets.
4. Do not use the Bluetooth headsets in a hazardous location.

Package includes

• Bluetooth Stereo Headsets x 1
• USB Charger (Cable) x 1
• User Manual x 1

Connection Diagram

Technical Specifications

How to use

Pairing to Mobile phone or other device

To use your Bluetooth Headsets, you must first pair your speaker with a phone or a computer. Once your Bluetooth Headsets is paired to a specific mobile phone, they will remain paired and automatically recognize each other whenever they are within range.

Pairing to a phone and Computer for Entertainment

1. Turn on your phone and ensure its Bluetooth function is activated.
2. Turn on the Bluetooth Headsets go to the paring mode.
3. Search your Bluetooth devices on your phone by following the phone's instructions.
   Refer to your phone's user manual for more information.
4. After a few second the phone will list the device as a discover device.
   Select it and follow your phone instruction to select this pairing.
5. Then your phone will request a passkey or PIN, enter "0000" as your PIN or passkey.
6. Your phone will confirm the pairing, and then press Yes/Ok.
7. Finally, select to connect with device from your phone.

Charging your device

The device is convenient to connect to AC charger or USB charger with Micro USB port marked with. Make sure that your device is full charged for at least 6 hours before initial use. Insert one terminal of your charger to AC main or USB port of PC and other terminal to Micro USB. While charging, the red LED light constantly. When charging is completed, the LED turns off.

• You must select a qualified charger or charging cable from a regular manufacturer.
• You must charge the Bluetooth Headsets if it has been not used for more than 12 months.

Service and Support

If your device is not performing as it should, please take it to your local service providers or dealer for service.

FAQ

Q1: Why is there no power even when the Speaker is power on?
A1: Ensure the battery is being charged up to 6 hours for first time using.
The LED is lighted when it starts charging.

Q2: There is no sound when playback.
A2: Check the connection between your device with phone or computer, if the connection is not established, please reconnect again. Make sure the Headsets device is paired and connected with your target phone or other master device.

Q3: How can I know the Bluetooth Headsets has been fully charged?
A3: It is full charging when the indicator LED turns red to green.

FCC Statement
This equipment complies with part 15 of FCC RF Rules. Operation is subject to the following two conditions:

1. This device many not cause interference and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

RF Warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Note: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: