Advertisement
Quick Links
Specifications
• Handmade in Italy since 1960
• ¼ Turn valves handmade at
Nicolazzi Factory
• Lead Free Brass Compliant to
AZ/NZS 3718
• Suitable even and uneven
pressure
• Handles are interchangeable
Further information Phone (03) 9761 4603
TWO HOLE BRIDGE SINK MIXER
Art: Z1459
Available replacement
handles:
-
El Capitan Handle
-
78 Mont Blanc Handle
- 18 Dame Anglaise
-
70 Half Dome
WM22315
AS/NZS3662
Canterbury Sink & Tap Co.
Max/Min Operating
Pressure: 100/500kPa
sales@sinkandtap.com.au
Advertisement
Related Manuals for CANTERBURY OFFICINA NICOLAZZI Z1459
Summary of Contents for CANTERBURY OFFICINA NICOLAZZI Z1459
- Page 1 • ¼ Turn valves handmade at Nicolazzi Factory • Lead Free Brass Compliant to AZ/NZS 3718 • Suitable even and uneven pressure WM22315 AS/NZS3662 • Handles are interchangeable Canterbury Sink & Tap Co. Max/Min Operating Pressure: 100/500kPa Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 2 Important Notice Model : Z1459 CAREFULLY READ THROUGH THESE INSTRUCTIONS BEFORE INSTALLATION AND USE OF ALL TAP WARE AND WALL VALVES INSTALLATION and WARRANTY INSTRUCTIONS TECHNICAL INFORMATION All flexible hoses are designed and manufactured for use with water in exposed locations only. Do not expose to household cleaners, chlorine, chloride, hydrochloric acid or other corrosive chemicals.
- Page 3 Installation Instructions Model : Z1459 Preparation ❶ Flush out the pipework to remove any foreign matter. The hot supply should be on the left when viewed from the front of the fitting. Measure and cut tap holes with spacing of 203 mm, centre to centre on the wash basin.
- Page 4 Installation Instructions Model :Z1459 ❹ Under the sink, place the supplied rubber gaskets C, onto the tap thread extensions. Then screw the mounting nuts D, onto the thread extensions. Screw the mounting nuts until the rubber gaskets mate up with the underside of the sink. ❺...
- Page 5 Installation Instructions Model : Z1459 ❺ Connect hot and cold water supplies to side valve inlet. Ensure all connections are firmly tightened. Before use Turn on the Hot and Cold supplies to the tap. Maximum temperature for Hot water supply to the tapware is 62 °C. ...
- Page 6 Spare Parts list Model : Z1459 Further information Phone (03) 9761 4603 sales@sinkandtap.com.au...
- Page 7 Care and Maintenance Instructions Model : Z1459 MAINTENANCE FOR TWO HOLE/TWO LEVER TAP WARE WITH TWO LEVER DESIGN INSTRUCTIONS FOR REPLACEMENT OF THE HOT OR COLD CARTRIDGE Do not replace the cartridge if there is low flow or no flow. Low flow or no flow is caused by obstruction or kinking of supply hoses.
- Page 8 Care and Maintenance Instructions Model : Z1459 Removing and replacing a handle MODEL SHOWN : Z1459 ❶ ❷ Loosen and unscrew the retaining flange Once totally loose, simply remove the A, from the tap body. handle from cartridge spline. ❸...
- Page 9 Care and Maintenance Instructions Model : Z1459 LOW FLOW OR NO FLOW TROUBLESHOOTING INSTRUCTIONS • Current kitchen taps have a max flow rate of 7 Litres per minute from the aerator. If you are experiencing low flow from the spout: Do not change the cartridge •...
- Page 10 Care and Maintenance Instructions Model : Z1459 Care of external finishes Nicolazzi products are all authentic finishes that have not been coated with any product. After each use, pat the fixture down to remove any excess water. This will prevent any water spotting or mineral build-up. Use only soft liquid soap and water to clean the surface.