Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for The Table Stable MB-3
- Page 1 MB-3 MODULATION BOX Instruction Manual The Table Stable Ltd. Phone: +41 (0)44 776 33 66 Im Grindel 6 Fax: +41 (0)44 776 33 65 8932 Mettmenstetten E-mail: info@tablestable.com Switzerland Internet: www.tablestable.com Vibration isolation technology made in Switzerland...
-
Page 3: Table Of Contents
Description ............................7 Connecting the box ........................... 7 Menu functions overview ........................8 Functions ............................10 Operation ............................11 Axis direction layout ........................12 Sales offices ........................... 13 Service order ..........................13 Specifications ..........................14 V 1.02 © The Table Stable Ltd. -
Page 4: Safety Instructions
Safety Instructions If you suspect the unit to be in any way unsafe, unplug and prevent any possible accidental usage. Contact your nearest service centre. Do not use in potentially explosive surroundings. For Indoor use only. For connection use only the D-Sub 15 cables (m/f) provided. Notes on equipment safety This system has been designed, manufactured and tested in conformity to the following community Directives/Regulations and Standards:... -
Page 5: Introduction
Thank you… …for your purchase of the MODULATION BOX MB-3. This unit has been designed specifically with performance and ease of use in mind. As with all Table Stable products, this device is made to the highest quality standards using precision electronics and mechanical components which should give you many years of trouble free use. -
Page 6: Front And Rear Panel
Front and rear panel Front panel Isolation switch on/off (TS systems only) Isolation on Indicator (TS systems only) Overload Indicator Modulation level of internal signal generator / external source selection Menu function selection / Enter Rear panel External signal input / Internal trigger output Output for TS-systems Output for AVI-systems Serial port (factory use only) -
Page 7: Description
Description Isolation switch (1) This switch allows you to switch the active Isolation on or off. (For TS-systems only) Isolation Indicator (2) This Indicator will light up when the active Isolation is enabled. (For TS-systems only) Overload Indicator (3) This Indicator will light up when the signal of the Internal/external generator is saturated. Mod.Level (4) Adjust to set the level of the internal signal generator in a range between MIN. -
Page 8: Menu Functions Overview
Menu functions overview Connecting the box to a running Isolation system will power up the box and the display will show the main page. Turn the MENU/SELECT knob (5) and push to enter into the modulation or setup menu. Push enter on top line to return to the previous page. To select a function within a menu push enter and turn the knob. - Page 9 Setup menu AVI-LP TS-LP V1 TS-LP V2 TS-C30 Custom 1 Custom 2 Custom 3 Custom 4 Custom 5...
-
Page 10: Functions
Functions Modulation menu The modulation menu allows you to select different exciting modes. OFF: All exciting signals are disabled Exciting in the vertical direction Exciting in the horizontal direction left to right Exciting in the horizontal direction front to rear Custom: 5 individual configurations of mixed signals can be recalled Internal signal generator... -
Page 11: Operation
Operation Switch on the isolation system and enable the isolation on the front panel/control unit. Set the isolation switch (1) on the modulation-box to ON. (TS-system only) Different excitation directions are selectable in the modulation menu. As the frequency of the excitation is scanned, the VELOCITY will remain approximately constant over the range 1-100Hz. -
Page 12: Axis Direction Layout
Axis direction layout TS-LP V2 from serial no. TS-150 LP: 1734 TS-140 LP: 822 TS-300 LP: 144... -
Page 13: Sales Offices
Our service department will contact you by return. If it proves to be necessary to return the system for repair, you will be issued with an RMA number which should then appear on all shipping documents The Table Stable Ltd. Phone: +41 (0)44 776 33 66... -
Page 14: Specifications
Specifications Input signal: Sine, square, triangle wave, max. amplitude 20Vpp Built in signal generator: Sine, square, triangle wave, 1-100Hz Safety Class: Protection class: IP 20 170×130×55mm (L×W×H) Dimensions: Weight: 630g Temperature range: 5°-40°C / 41°-104°F Relative humidity: 10-90% (5°-30°C / 41-86°F), 10-60% (30°-40°C / 86°-104°F) Application: Indoor Altitude:...
Need help?
Do you have a question about the MB-3 and is the answer not in the manual?
Questions and answers