Advertisement
Quick Links
I N S T A L L A T I O N
APPLICATION
FJ Cruiser
M A N U A L
INSTALLATION TIME
Installation time is less than 3 hours depending on proficiency
TOOLS
Attention
:
We highly recommend you to find professional store to install the product
Attention
:
If not follow the instruction may damage the ECU, motor or the car
YEAR
2005+
0.5
1
2
3
Advertisement
Summary of Contents for YTPIONEER Electric Side Step
- Page 1 I N S T A L L A T I O N M A N U A L APPLICATION YEAR 2005+ FJ Cruiser INSTALLATION TIME Installation time is less than 3 hours depending on proficiency TOOLS Attention We highly recommend you to find professional store to install the product Attention If not follow the instruction may damage the ECU, motor or the car...
-
Page 2: Components List
C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + COMPONENTS LIST Wire harness: Signal controller one set for motor power and signal Running board 2 pcs Screw package RR idler bracket... -
Page 3: Installation
C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Electrical part diagramin Installation According to the schematic cable： 1. Take the power supply from the positive and negative poles of the battery。... - Page 4 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Electrical part installation (The following models are different, the method is the same) Open the motor cover ，...
- Page 5 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Harness Controller accessories 1.Wireless Magnetic Control Signal Transmitter; 2, ECU 1---Connectors to the Electric Power; 2/3--- with wireless magnetic control signal receiver;...
- Page 6 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Open the engine bay cover, connect the power cables to the car battery(Note: Red for positive Pole and Black for Negative Pole), thread the other cables along the Wheel Eyebrow through the nearby holes to the Chassis bottom, connect the plugs with Motors.
- Page 7 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Install the sensor and magnetic iron: ①Open the door, find the door sill bar and disassemble At the inner part of the door sill bar, find a spare position without metal, which is near outside and backward, stick the sensor there,...
- Page 8 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Install the sensor and magnetic iron: ①Open the door, find the door sill bar and disassemble The magnet is attached to the Pierce the fading ink bottle with edge of the mark and the...
- Page 9 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Mechanical part installation 1.Organize the string with tie tape,Install the removed guard plate in its original position【If there is interference between the guard plate and the bracket,the interference part should be removed】...
- Page 10 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Install running board (2 sides in same way to install) 1 , 2 Use M6 ×...
- Page 11 C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Testing and adjust the balance Insert fuse again. Then open and close doors to let step work.
-
Page 12: Automatic Stop
C r u i s e r E l e c t r i c S i d e S t e p 2 0 0 5 + Automatic power deploy: The running boards will extend down and out when the door is opened. Automatic stop: If an object is in the way of the moving running board, the running board will automatically stop.